Garmin GPSMAP 536s Flush Mount Kit Installation
October 2007
Part Number 190-00553-01 Rev. B
Printed in Taiwan
Installing the Flush Mount Kit
Use this kit to flush mount a GPSMAP 500 series unit into a flat panel.
Select an appropriately sized location for the unit.
Use the Flush Mount Template provided to determine a location.
Check that all cables reach the unit mounting location.
Always wear safety goggles and a dust mask when drilling, cutting, or sanding.
Included mounting hardware—(1) unit housing, (1) rubber seal, (2) tension mount brackets, (4) hex bolts, (4) hex nuts, and (4) wing nuts.
Tools (not included)—drill, 3/8" (10 mm) drill bit, jig saw, and a 9/32" (7 mm) wrench.
To install the Flush Mount Kit:
1. Cuttheopening:
The flush mount template has adhesive on the back. Remove the protective liner and apply the template to the location you want to
mount the unit.
Using a 3/8" (10 mm) drill bit, drill the pilot holes indicated on the template to begin cutting the mounting surface.
Using the jig saw, cut the mounting surface along the inside of the line indicated on the template. Be very careful when cutting this
hole, because there is only a small amount of clearance between the unit housing and the tension mount arms. Cut slightly inside the
indicated line and then sand or file the panel as needed to obtain the best fit.
2. Assemble the flush mount hardware (see Figure 1):
Attach the rubber seal to the front of the unit housing.
Insert the four hex bolts into the unit housing so they stick out of the back.
Use the four hex nuts to secure the hex bolts to the unit housing. Using the 9/32" (7 mm) wrench, tighten the nuts without
overtightening.
Slide the unit into the unit housing. (If you have limited space behind the mounting surface, this can be done in step 3.)
When the unit is inserted correctly, it will snap into place within the unit housing.
Connect the wiring harness, GPS antenna, and XM antenna (if applicable) to the unit. (This can also be done in step 3, if necessary.)
Unit
Rubber seal
Hex bolts
Hex nuts
Hex nuts
Hex bolts
Figure 1
Unit housing
•
•
•
•
•
•
•
•
•
•
•
•
•
EN
Also See for Garmin GPSMAP 536s
Related Manuals for Garmin GPSMAP 536s
-
Garmin GPS RV 760LMT Owner's Manual
24 pages
-
Garmin GPS nuvi 2597LMT Owner's Manual
22 pages
-
Garmin GPS nuvi 2797LMT Owner's Manual
22 pages
-
Garmin GPS echoMAP 50s Owner's Manual
38 pages
-
Garmin GPS nüvi 760 Owner's Manual
66 pages
-
Garmin GPS GPSMAP 2010/2010C Owner's Manual
104 pages
-
Garmin GPS eTrex 20 Owner's Manual
60 pages
-
Garmin GPS GPSMAP 62 Owner's Manual
60 pages
-
Garmin GPS Oregon 650 Owner's Manual
22 pages
-
Garmin GPS Oregon 650t Owner's Manual
22 pages
-
Garmin GPS GPS 12 Owner's Manual
66 pages
-
Garmin GPS GPSMAP 76 Owner's Manual
86 pages
-
Garmin GPS Edge Touring Plus Owner's Manual
14 pages
-
Garmin GPS Forerunner 305 Owner's Manual
80 pages
-
Bushnell GPS BackTrack Point >3 Owner's Manual
60 pages
-
Garmin GPS nuvi 2595 Owner's Manual
88 pages
-
Garmin GPS nuvi 52LM Owner's Manual
32 pages
-
Parrot GPS CK3100 LCD User's Manual
26 pages
-
Garmin GPS GPS GNS 430W User's Manual
22 pages
-
Garmin GPS NUVI 265W User's Manual
60 pages
-
Garmin GPS Approach S2 Owner's Manual
4 pages
-
Garmin GPS eTrex 20x Owner's Manual
60 pages
-
Garmin GPS eTrex 30x Owner's Manual
60 pages
-
Garmin GPS Nuvi 1450 Owner's Manual
72 pages