Garmin GMR 606 User's Manual | Page 8
8
GMR 600/100 Series Installation Instructions
Installing the Field-Installable RJ-45 Network Connector (Optional)
A field-installable RJ-45 network connector is provided for you to create a network cable that is the correct length for your installation.
➊ O-Ring
➋ RJ-45 modular plug
➌ Ethernet cable termination
Copper tape strip (not shown)
➊
➋
➌
Preparing the Network Cable
1. Cleanly cut your Ethernet cable to the desired length. Retain the cut RJ-45 connector for Step 4.
2. Remove the strain-relief nut from the cable-connection housing and slide it onto the cut end of the cable as shown.
3. Feed the cut cable end through the connection housing as shown.
Strain relief
Cut end of cable
Connection
housing
4. Examine the RJ-45 connector removed in Step 1 and compare it to the wire positions in the table below. Note which cable side, A or B, was
removed in Step 1.
Position
Wire Color—Main/Stripe
Side A
Side B
1
White/Orange
White/Green
2
Orange
Green
3
White/Green
White/Orange
4
Blue
Blue
5
White/Blue
White/Blue
6
Green
Orange
7
White/Brown
White/Brown
8
Brown
Brown
nOTe: The Garmin Marine Network requires cross-over cables not exceeding 100 meters between devices. When constructing a custom cable
from bulk wire, you must create both a Side A and Side B.
5. Prepare the cable for plug installation:
Using a sharp knife, insert the blade between the cable shield and jacket. Slit the jacket 5/8" back from the
trimmed end of the cable.
Peel the jacket back and remove the slit portion.
TrimtheshieldandMylarfilmawayfromwires.Becarefulnottocutanyofthewires.
Fold the drain wire back over the jacket and trim to approximately 9/16 in. (14 mm).
Untwist the wire pairs enough to ensure a proper connection.
Arrangeindividualwiresinproperorderaccordingtothetableshownabove.Forexample,ifyouhaveidentified
the end of the cable in Step 4 as Side A, arrange the wires for Side A. If you are constructing a custom cable
from bulk wire, you need to make both a Side A and a Side B connection.
Trim the wire ends to an even length, leaving approximately 9/16 in. (14 mm) from the ends to the jacket edge.
Place the drain wire on the jacket. Wrap the supplied copper tape around cable as close to the edge of the jacket as possible.
Using a pair of pliers, squeeze the copper tape to pre-form the cable jacket end for easier insertion into the plug. Use caution to avoid
damaging the copper tape.
•
•
•
•
•
•
•
•
•
Position 1
Position 8
Position 1
9
/16 in.
(1 mm)
Drain
wire
9
/16
(1
Drain
wire
Related Manuals for Garmin GMR 606
-
Cobra Radar Detector ESD 7570 Operation Manual
13 pages
-
Cobra Electronics Radar Detector ESD 7100 Operating Instructions
11 pages
-
Cobra Electronics Radar Detector ESD-9000 User's Manual
15 pages
-
Cobra Electronics Radar Detector ESD 7000 Operating Instructions
12 pages
-
Uniden Radar Detector LRD 6199SWS User's Manual
25 pages
-
Uniden Radar Detector LRD 2200SWS User's Manual
26 pages
-
Uniden Radar Detector BC248CLT User's Manual
42 pages
-
Oregon Scientific Radar Detector BAR206 User's Manual
10 pages
-
Whistler Radar Detector TOTAL BAND PROTECTION XTR-265 User's Manual
9 pages
-
Whistler Radar Detector XTR-540 User's Manual
9 pages
-
Whistler Radar Detector XTR-195 User's Manual
9 pages
-
Whistler Radar Detector 1743 1744 User's Manual
7 pages
-
Whistler Radar Detector 1732 User's Manual
9 pages
-
Whistler Radar Detector XTR-140 User's Manual
9 pages
-
Whistler Radar Detector XTR-550 User's Manual
9 pages
-
Whistler Radar Detector LASER-RADAR XTR-130 User's Manual
9 pages
-
Whistler Radar Detector XTR-150 User's Manual
9 pages
-
Lowrance electronic Radar Detector X-85 User's Manual
51 pages
-
Escort Radar Detector PASSPORT 7500 User's Manual
14 pages
-
Escort Radar Detector Passport 9500i User's Manual
6 pages
-
Furuno Radar Detector FAR-2827 User's Manual
8 pages
-
Furuno Radar Detector FAR-2837S User's Manual
130 pages
-
Furuno Radar Detector FR-1510 MARK-3 User's Manual
4 pages
-
Whistler Radar Detector XTR-330 User's Manual
9 pages