Garmin Delta Upland Owner's Manual | Page 7

Garmin Dog Tracking & Training Owner's Manual - Delta Upland.
Download
Page  of 14
4.1, 1658 votes
background image

Beeper Sounds
The beeper device can emit two sounds: a beep and a hawk scream. These sounds indicate your dog's hunting and pointing status.
While your dog is hunting, the beeper device emits a series of one to three beeps every four seconds. You can select the number of 

beeps in the series, which is useful to distinguish between multiple dogs. You can also disable this sound so that the beeper device 

is silent while your dog is hunting.
When your dog is pointing, the beeper emits either one beep every second or one hawk scream every five seconds, depending on 

the setting you choose.
When you select beeper sounds, the selected sounds are indicated briefly by the status LEDs. The red status LED indicates the 

hunting sound, and the green status LED indicates the pointing sound.

Mode Red LED Hunting Sound Green LED Pointing Sound
1

1 blink

1 beep

Solid

Hawk scream

2

2 blinks

2 beeps

3

3 blinks

3 beeps

4

Off

Silent

5

1 blink

1 beep

Blinking

Beep

6

2 blinks

2 beeps

7

3 blinks

3 beeps

8

Off

Silent

Customizing the Beeper Sounds
With the device turned on, hold the power key until both 

LEDs blink rapidly three times, and release the power key.

Select the power key to cycle through the sound modes.

Each time you select the power key, the LEDs indicate the 

selected sound mode. You may have to cycle through 

several sound modes to reach your preferred sound mode.

Hold the power key until both LEDs blink rapidly three times, 

and release the power key to set the sound mode to the 

current selection.

Resetting to the Default Beeper Sounds
You can reset your beeper device to the factory default sound 

settings, regardless of the current setting or power state of the 

device.

Hold the power key for 15 seconds.
The device emits a high-low, high-low beep sequence, and 

the LEDs flash to confirm the reset.

The next time you turn on the device, it is set to mode 1.

Introducing Your Dog to the Beeper Device
The beeper device is loud and may startle an inexperienced 

dog. You should introduce your dog to the device before you 

use it during a hunt. You can use any of these methods to help 

your dog adjust to the sounds.
• Place a piece of duct tape over the speaker opening to 

muffle the sounds during your first use of the device on the 

dog.

• Turn on the device, and place it near your dog's kennel for 

several hours.
This allows the dog to hear and adjust to the sounds in a 

comfortable location.

Turning the Beeper Sounds On or Off 

Remotely
Before you can turn the beeper sounds on or off remotely, the 

dog collar device and the beeper device must be turned on.
You can use the handheld device to turn the beeper sounds on 

or off remotely. Turning off the beeper sounds does not turn off 

the beeper device.
On the handheld device, select a training mode in which a 

training key is assigned to the beeper device.

Select the training key assigned to the beeper device to turn 

the beeper sounds on or off for the selected dog.

Locating Your Dog Using the Beeper Device
You can remotely trigger the beeper device to emit a series of 

beeps, which you can use to determine the location of your dog.
On the handheld device, select the dog to locate (Selecting a 

Dog Collar Device).

Select a training mode in which a training key is assigned to 

B (Selecting a Training Mode).

Hold the training key assigned to B.
The beeper device emits a series of beeps for as long as you 

hold the training key, up to eight seconds.

Dog Training

You should research and investigate the training methods best 

suited for you, your dog, and your needs. This manual provides 

some basic guidelines for training, but each dog has unique 

training needs.
When used properly, the Delta Upland training system is a very 

effective training tool to aid your dog in reaching its full potential. 

The use of the training system should be part of an overall 

training program.
Begin training your dog on a leash, without the Delta Upland 

training system. You should train your dog how to heel, sit, and 

come to you. After the dog understands these three basic 

commands, you can begin training with the dog collar device 

and the leash. Finally, when the dog consistently obeys 

commands using the leash and collar, you may be able to 

remove the leash to train with only the dog collar device.

Fitting the Collar on Your Dog

 CAUTION

To prevent irritation from the contact points, remove the collar 

for at least eight hours out of every 24-hour period.
This device is not intended for human use. Do not attempt to 

use on any person.

NOTICE

Before you put the collar on the dog, remove the charging clip. If 

you do not remove the clip, it may become detached from the 

collar and become lost.

Dog Training

3

Related Manuals for Garmin Delta Upland

0.573142s