Frigidaire FFSC2323LS Installation Instructions

Frigidaire Air Conditioners Installation Instructions - FFSC2323LS.
Download
Page  of 2
4.2, 1364 votes
background image

This document should only be removed by customer after installation. 

P/N: 241811505

Not  satisfied with the installation of your refrigerator?

   Please contact the store you purchased it from.

Installation Instructions for Side-by-Side Refrigerator

2

3

To connect the water supply to the rear of your refrigerator:
  1  Ensure that the refrigerator is not plugged in.

  2  Flush the supply line until water is clear by placing the end of the 

copper tube in a sink or bucket and opening the shut-off valve.

  3  Remove the plastic cap from the water valve inlet at the rear of 

your refrigerator. Discard the cap.

  4  Slide the brass compression nut, then the ferrule (sleeve) onto 

copper tube.

  5  Push the copper tube into water valve inlet as far as it wil  go 

(1/4 inch).

  6  Slide the ferrule (sleeve) into valve and finger-tighten the 

compression nut onto valve. Tighten another half turn with a 

wrench. Do not over-tighten.

  7  Secure the copper tube to your refrigerator’s rear panel with a 

steel clamp and screw (see illustration).

  8  Coil the excess copper tubing (about 2½ turns) behind your 

refrigerator as shown. Arrange coiled tubing to avoid vibration or wear against other surfaces.

  9  Open water supply shut-off valve and tighten any connections that leak. 

5

(continued)

6

7  

1

4

5

8

Doors

 Door seals completely to cabinet on all

      sides

 Doors are level
Leveling

 Refrigerator is level, side to side and tilted

      1/4” (6mm) front to back

 Toe grille is properly attached to

      refrigerator

 Cabinet is sitting solid on all corners
Electrical Power

 House power turned on
 Refrigerator plugged in

Ice Maker

 House water supply connected to

      refrigerator

 No water leaks present at al  connections 

      - recheck in 24 hours

 Ice Maker is turned ON.
 Ice & Water Dispenser operates correctly
 Front filter must be flush with filter 

      housing (some models)
Final Checks

 Shipping material removed
 Fresh Food and Freezer temperatures set
 Crisper Humidity controls set
 Registration Card sent in

 Installation Checkoff List

Prepare The Installation Site

Transport Unpackaged Refrigerator To Site

Your refrigerator is designed to be part of a built-

in kitchen cabinet system. Be sure to coordinate 

site preparation and installation with your kitchen 

contractor.  Include these minimum guidelines in your site 

preparation:

  •  Choose a place near a grounded electrical outlet.

  •  Do not use an extension cord or an adapter plug.

  •  Avoid direct sunlight and close proximity to a range, 

dishwasher or other heat source.

  •  Floor should be level and able to support a ful y 

loaded refrigerator.

  •  The refrigerator’s Ice & Water Dispenser requires 

water supply access. 

  •  Plan for easy access to counter tops when 

    removing food.

  •  For complete access to drawers and freezer 

baskets, doors must be able to fully open.

Allow the following clearances for ease of installation, proper air circulation, and plumbing and 

electrical connections:  Sides & Top: 3/8 inch / Rear: 1 inch

By now, you have already removed your refrigerator’s shipping carton. 

You may still need to use a hand truck to move it through close spaces or 

entrances. If the refrigerator is larger than an entrance, consider two options:
  •  Remove the entrance door if one exists.

  •  Remove the refrigerator doors (see how in your Use & Care Guide). 
When using a hand truck:
  •  Load refrigerator from side of cabinet only.

  •  Do not run retaining straps over handles.

  •  Do not over-tighten retaining straps.

  •  Never use refrigerator handles to move the 

refrigerator.

  •  Remove tape from doors only after unit is in place.

Connect Water Supply

What you will need:
  •  Access to a cold 

water line with 

pressure of  

30-100 psi.

  •  Copper tubing 

with ¼-inch 

(6.4mm) OD. 

Length for this tubing is the distance 

from the rear of the refrigerator to your 

household water supply line plus 7 

feet (2.1 meters). 

  •  A shut-off valve for the connection 

between your household water line and 

the refrigerator supply line. Do not use 

a self-piercing shut-off valve.

  •  A compression nut and ferrule (sleeve) 

for the water supply connection at the 

rear of your refrigerator.

Place In Permanent Position

If possible, use a hand truck to position the refrigerator directly in front of its cabinet enclosure. 
Be careful not to move the refrigerator beyond its water supply (copper tubing) connections.
Plug in the power cord, and push the refrigerator 

straight back into place.

Level Refrigerator & Adjust Doors (if necessary)

Problems? Try These Suggetions

What’s Next?

Congratulations. You are ready to begin enjoying your new refrigerator. 
  •  To become aware of important safety instructions and learn how to operate your 

refrigerator, please read the entire Use & Care Guide.

  •  You may want to start with the “Normal Operating Sights & Sounds” section of the Guide to 

learn more about what to expect during typical operation.

  •  Please register your product. You can register online at www.electroluxusa.com. or you can 

simply send in the Registration Card.

And thank you for choosing Frigidaire.

WARNING

To avoid electric shock, which can cause death or severe personal injury, do not connect your 

refrigerator to an electrical power source until you have completed Step 3 of these instructions.

CAUTION

Room temperatures below 55°F 

(13°C) or above 110°F (43°C) 

will impair cooling ability of your 

refrigerator’s compressor.

IMPORTANT

If you are instal ing your refrigerator without 

connecting it to a water supply, make sure the ice 

maker’s power switch is turned Off (see the Use & 

Care Guide for more details).

 NOTE

These installation instructions 

are provided only as a possible 

customer option. We recommend 

that you use a service or kitchen 

contracting professional to install 

your refrigerator.

 NOTE

Information about cabinetry 

construction for your new appliance 

is available for contractors. Call 

1-877-435-3287.

CAUTION

Shifting the refrigerator from side to 

side may damage flooring.

 NOTE

Kit #53039117950, available from your dealer, 

provides al  materials for a water supply 

instal ation, including 25 feet of copper tubing and 

full instructions.

CAUTION

To avoid property damage:

•  Use copper tubing for the water supply line (plastic 

tubing is more likely to leak).

•  Ensure water supply complies with local 

plumbing codes.

CAUTION

•  Shifting the refrigerator from side 

to side may damage flooring.

•  Do not block the toe gril e on the 

lower front of your refrigerator. 

Sufficient air circulation is essential 

for proper operation.

 NOTE

•  The ice maker’s fil  valve may operate noisily if the household water supply is shut off.
•  After ensuring no water leaks exist at any connection, be sure to check for leaks again in 24 hours. 
•  See your Use & Care Guide for detailed information about setting up and operating the Ice & 

Water Dispensing system.

1

2

3

Hinge
Flange

Set Screw
(some models)

Door Stop
Flange

Hinge

Open Door

7/16” Wrench

and 3/32” Hex Key

(some models)

4

To level the doors using the adjustable lower hinge (Type 2 without set screw)
  1  If the refrigerator door is lower than the freezer door, raise the refrigerator door by turning 

the adjustment screw clockwise using a 7/16 inch wrench. (See illustration 3.)

  2  If the freezer door is lower than the refrigerator door, raise the freezer door by turning the 

adjustment screw clockwise using a 7/16 inch wrench. (See illustration 3.)

  3  After leveling, verify door stop contacts lower hinge and top of door does not contact upper 

hinge through ful  movement of door (from ful y closed to 

fully open). (See illustration 5.)

  4  To replace the toe gril e, open both doors.  Slide left and 

right sides of toe gril e over lower hinges of refrigerator. 

While pushing toe gril e firmly against cabinet, fasten 

bottom clips of toe gril e to cabinet. Fasten top clips to 

cabinet. Close the doors.  Fasten right and left side clips 

into groove of bottom hinge.

Guidelines for final positioning of your refrigerator:
  •  All four corners of the cabinet must rest firmly on the floor.

  •  The cabinet should be level at the front and rear.

  •  The sides should tilt ¼-inch (6 mm) from front to back (to 

ensure that doors close and seal properly).

  •  Doors should align with each other and be level.
To level the cabinet using the front rollers:
  1  With both doors closed, unfasten right and left side clips 

of toe gril e from bottom hinge groove  Open both doors. 

Press firmly on top of toe gril e until top of toe gril e pops 

off. Pull toe grille outward toward your body and off of lower hinges.  

(See illustration 1.)

  2  Close the doors and use a flat-blade screwdriver or 3/8 

inch socket wrench to raise or lower the front rol ers. (See 

illustration 2.)

  3  Ensure both doors are bind-free with their seals touching the 

cabinet on all four sides.

To level the doors using the adjustable lower hinge (Type 1 

with set screw):
  1  Before leveling either door, remove set screw that locks door height into position. (The door 

cannot be adjusted without set screw removed.)

  2  If the refrigerator door is lower than the freezer door, raise the refrigerator door by turning 

the adjustment screw clockwise using a 7/16 inch wrench. (See illustration 3.)

  3  If the freezer door is lower than the refrigerator door, raise the freezer door by turning the 

adjustment screw clockwise using a 7/16 inch wrench. (See illustration 3.)

  4  After leveling, verify door stop contacts lower hinge and top of door does not contact upper 

hinge through full movement of door (from fully closed to fully open). (See illustration 4.)

  5  Reinstall set screw, locking the door height.

  6  To replace the toe grille, open both doors.  Slide left and right sides of toe grille over lower 

hinges of refrigerator. While pushing toe gril e firmly against cabinet, fasten bottom clips of 

toe gril e to cabinet. Fasten top clips to cabinet. Close the doors.  Fasten right and left side 

clips into groove of bottom hinge.

5

Operation problems are possible if any of the instal ation tasks are not completed. Here is a list 

of things to check for:
  •  Is the refrigerator’s power cord plugged in?

  •  Is the refrigerator connected to the household water supply?

  •  If you had to remove the refrigerator and freezer doors, did you reattach water and power 

connectors at the door hinges? (See the Use & Care Guide for detailed instructions on 

removing and replacing doors.)

  •  Is the ice maker power switch turned On?
Other possibilities to check:
  •  Is the power to the receptacle turned on?

  •  Is the water filter above the fresh food compartment fully seated (see Use & Care Guide for details)?
If you stil  have operation problems after checking these suggestions, please see the “Solutions 

To Common Problems” section in your Use & Care Guide. 

Related Manuals for Frigidaire FFSC2323LS

0.542912s