Fluke 3000 FC User's Manual

Fluke Multimeter User's Manual - 3000 FC.
Download
Page  of 24
4.1, 2443 votes
background image

 

®

 

PN 

1631798   December 2001, Rev. 1, 1/13  

© 2001 Fluke Corporation. All rights reserved.

 

 

 

 T5-600 

T5-1000 

 Electrical 

Tester 

 Safety 

Sheet

(English) 
 Read First: Safety Information 



 Warning 

To prevent possible electrical shock, fire, or personal injury: 
• 

Use the Product only as specified, or the protection 
supplied by the Product can be compromised. 

• 

Read all safety information before you use the Product. 

• 

Carefully read all instructions. 

• 

Do not use and disable the Product if it is damaged. 
Protection may be impaired. 

• 

The battery door must be closed and locked before you 
operate the Product. 

• 

Examine the case before you use the Product. Look for 
cracks or missing plastic. Carefully look at the insulation 
around the terminals. 

• 

Comply with local and national safety codes. Use personal 
protective equipment (approved rubber gloves, face 
protection, and flame-resistant clothes) to prevent shock 
and arc blast injury where hazardous live conductors are 
exposed. 

• 

Measure a known voltage first to make sure that the Product 
operates correctly. 

• 

Replace the batteries when the low battery indicator shows 
to prevent incorrect measurements. 

• 

Do not use the Product around explosive gas, vapor, or in 
damp or wet environments. 

• 

Do not apply more than the rated voltage, as marked on the 
Product, between terminals or between any terminal and 
earth ground. 

• 

Do not touch voltages > 30 V ac rms, 42 V ac peak, or 60 V 
dc. 

• 

Keep fingers behind the finger guards on the probes. 

• 

Connect the common test lead before the live test lead and 
remove the live test lead before the common test lead. 

• 

Clean the case with a damp cloth and detergent. Do not use 
abrasives or solvents. 

• 

Remove the batteries if the Product is not used for an 
extended period of time, or if stored in temperatures above 
50 °C. If the batteries are not removed, battery leakage can 
damage the Product. 

• 

Limit operation to the specified measurement category, 
voltage, or amperage ratings. 

• 

Use the correct terminals, function, and range for 
measurements. 

• 

Hold the Product behind the tactile barrier. 

• 

Do not use test leads if they are damaged. Examine the test 
leads for damaged insulation, exposed metal, or if the wear 
indicator shows. Check test lead continuity. 

• 

Use only current probes, test leads, and adapters supplied 
with the Product. 

• 

Do not exceed the Measurement Category (CAT) rating of the 
lowest rated individual component of a Product, probe, or 
accessory. 

• 

Repair the Product before use if the battery leaks. 

• 

Be sure that the battery polarity is correct to prevent battery 
leakage. 

• 

Do not operate the Product with covers removed or the case 
open. Hazardous voltage exposure is possible. 

• 

Use only specified replacement parts. 

• 

Have an approved technician repair the Product. 

• 

Disconnect power and discharge all high-voltage capacitors 
before you measure resistance, continuity, capacitance, or a 
diode junction. 

Symbols 

 

Hazardous voltage. Risk of electric shock. 

 

Risk of Danger. Important information. See Manual. 

Double Insulated 

Battery 



Conforms to relevant North American Safety 
Standards. 

Conforms to EU directives. 

Earth 

DC (Direct Current) 

AC (Alternating Current) 



Certified by Underwriters Laboratories. 

Conforms to relevant South Korean EMC Standards. 

 

Conforms to CAN/CSA-C22.2 No. 61010-1, second 
edition, including Amendment 1. 

VDE  (Verband Deutscher Electroniker) 

Conforms to relevant Australian EMC requirements. 

CAT II 

Measurement Category II is applicable to test and 
measuring circuits connected directly to utilization 
points (socket outlets and similar points) of the low-
voltage MAINS installation. 

CAT III 

Measurement Category III is applicable to test and 
measuring circuits connected to the distribution part of 
the building’s low-voltage MAINS installation. 

CAT IV 

Measurement Category IV is applicable to test and 
measuring circuits connected at the source of the 
building’s low-voltage MAINS installation. 

 

This product complies with the WEEE Directive 
(2002/96/EC) marking requirements. The affixed label 
indicates that you must not discard this 
electrical/electronic product in domestic household 
waste. Product Category: With reference to the 
equipment types in the WEEE Directive Annex I, this 
product is classed as category 9 "Monitoring and 
Control Instrumentation" product. Do not dispose of 
this product as unsorted municipal waste. Go to 
Fluke’s website for recycling information. 

Limited Warranty and Limitation of Liability 

This Fluke product will be free from defects in material and workmanship 
for 2 years from the date of purchase. This warranty does not cover fuses, 
disposable batteries, or damage from accident, neglect, misuse, alteration, 
contamination, or abnormal conditions of operation or handling. Resellers 
are not authorized to extend any other warranty on Fluke’s behalf. To 
obtain service during the warranty period, contact your nearest Fluke 
authorized service center to obtain return authorization information, then 
send the product to that Service Center with a description of the problem. 
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, 
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED 
OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING 
FROM ANY CAUSE OR THEORY. Since some states or countries do not 
allow the exclusion or limitation of an implied warranty or of incidental or 
consequential damages, this limitation of liability may not apply to you.

 

Fluke Corporation 
P.O. Box 9090 
Everett, WA  98206-9090 
U.S.A.

 
Fluke Europe B.V. 
P.O. Box 1186 
5602 BD Eindhoven 
The Netherlands

11/99 

To register your product, visit http://register.fluke.com.

0.682971s