Extron electronic S1 26W User's Manual

Extron electronic Speakers User's Manual - S1 26W.
Download
Page  of 1
4.5, 1096 votes
background image

Trace template

1

Cutout Template

Determine the speaker location.
Leave at least 1” clearance from the edge of the speaker
to the studs in all directions.  Hold or tape template in location,
make sure template is level.  Trace along the inside of the template.

4

Insert the speaker into the wall opening.
Loosen the six screws on the front baffle (counter-
clockwise) 1/2 turn.  Then tighten the screws (clockwise)
until the dog legs clamp the speaker to the wall.

5

6

Level speaker, position each wall clamp outward, and tighten
each screw until snug.
Install dust shield to protect the speaker during ongoing
construction.

Remove the dust shield,
install the speaker grill.

Dust Shield

Paint Guard

188 mm x 275 mm

(7.4” x 10.8”)

Application diagram:

Specifications:

2

Carefully cut a hole along the inside of the traced line.

3

Attach the speaker wires to the 2-pole captive screw plug.
Use red for the positive (+) wire and black for the negative (-)
wire.  Insert the 2-pole captive screw plug into the 2-pole
connector on back of the speaker.

RS-

23

2/M

LC/IR

Tx

Rx

IR

12V

A

B

C

PRE

AM

P

100-240

V

1.0A

 MA

X.

50-60H

z

AU

DIO 

INPU

TS

LIN

E L

EV

EL

MO

NO

AU

DIO

AU

DIO

LIN

EOU

T

AU

X/M

IX

AD

JUST

-42d

B

TO

+24d

B

L

R

L

R

R

1

2

INPU

TS

OU

TPU

TS

VID

EO

H

V

B

G

R

1

2

INPU

TS

MO

NIT

OR

 OU

T

5

6

RIGH

T

LE

FT

AM

PLI

FIED

 OU

TPU

T

R

Extron
MLS 304SA
MediaLink  Switcher

SI 26W
Two-way In-wall
Speaker

Laptop

w/ Audio

Projector

VCR

PC

Acoustic & Electrical

General

Speaker type..................................  2-way in-wall speaker
Frequency range...........................   40 Hz to 20 kHz, -10 dB, half space
Power capacity..............................   60 W continuous program,
 

30 W continuous pink noise

Nominal sensitivity......................      89 dB, 1 W, 1 m, half space
Nominal impedance ....................     8 ohms
Crossover frequency...................      2.5 kHz
Woofer...........................................   6.5" (165 mm) polypropylene cone with  
 

moisture resistant coating

Tweeter..........................................   0.75" (19 mm) titanium dome

Temperature/humidity...............  

Storage: -40 to +158 °F (-40 to +70 °C) /  

 

10% to 90%, noncondensing

 

Operating: +32 to +122 °F (0 to +50 °C) /  

 

10% to 90%, noncondensing

Warranty .......................................  5 years parts and labor

NOTE:   All nominal levels are at ±10%.
NOTE:   Specifications are subject to change without notice.

SN

 XX

XX

XX

XX

 E 

XX

XX

X 0

0/0

0

Imped

anc

e

8 O

hm

s

Engin

eered in

 USA

SI 26W

In-W

all Sp

eaker

At least 1” from the stud.

Print at 100%. - Do Not “Fit to Paper”.

Cut material

Do not over-tighten screws.

CAUTION

SI 26W

In-Wall Speaker

User’s Guide

68-1101-01 

Rev A

08 07

0.632361s