Extron electronic Extron Electronics Projector PMK 300 User's Manual

Extron electronic Projectors User's Manual - Extron Electronics Projector PMK 300.
Download
Page  of 1
4.6, 1218 votes
background image

Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500  
Fax 714.491.1517

Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040  
Fax +31.33.453.4050

Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400  
Fax +65.6383.4664

Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan 
+81.3.3511.7655  
Fax +81.3.3511.7656

www.extron.com

68-993-01

Rev. B 12 05

PMK 300 Multi-Product Projector Mounting Kit

Installation Instructions

N  Only VersaTools products and most IP Link products can be 

mounted using the multi-product projector mounting kit.

1

.  If necessary, remove the feet from the bottom of the device to be 

installed.

2

.  Mount the device(s) to any of the bracket’s three mounting 

plates.  The device(s) can be vertically mounted facing either 
up or down, whichever is most convenient.  See fi gure 1 on the 
other side of this card.

N  On the side mounting plates, the device is typically mounted on 

the outside of the bracket.
On the front mounting plate, the device is typically mounted on 
the inside of the bracket.

a

.  For a VersaTools or IP Link device, use two supplied 

4-40 x 3/16 screws in opposite (diagonal) corners to 
secure the device to the bracket.

b

.  For a power supply, use the two included tie wraps to 

strap the power supply to the bracket.

N  The PMK 300 has a hole in the bottom plate that allows the 

projector pole to be inserted through the center of the plate 
rather than outside of the plate (see fi gure 2 on the other side of 
this card).  To install the PMK 300 in this confi guraion, slide 
the bracket up from the bottom of the pole before the projector is 
installed on the pole.

3

. Affi x the supplied rubber pad to the side of the U-bolt clamping 

plate that the projector pole contacts.

4

.  Place the U-bolt around the ceiling pole and insert the two legs 

of the U-bolt through the slotted holes on the bracket’s clamping 
plate and then through the round holes on the backing brace.

 

For a typical (1.5“ to 2.0“ diameter) pole — 

The supplied U-bolt 

fi ts a typical ceiling pole.

 

For a smaller or larger pole — 

Locally obtain a U-bolt that fi ts 

the ceiling pole.  The slotted holes on the bracket can accomodate 
a U-bolt for pole sizes from 1.0“ to 2.5“ in diameter.

5

.  Secure the bracket to the U-bolt with the included hex nuts, 

washers, and lock washers.  Use a proper-sized socket to tighten 
the hex nuts.

PMK 300 Multi-Product Projector Mounting Kit

Installation Instructions (continued)

Extron 
PMK 300 
Multi Product Projector 
Mount Kit 

U-Bolt

Rubber Pad 

Backing
Brace

Clamping
Plate

U-Bolt 

Extron 
PMK 300 
Multi Product Projector 
Mount Kit 

Rubber Pad

Clamping
Plate

Backing
Brace

Figure 1

Figure 2

0.560417s