Dell UltraScan 4476T User's Manual

Dell Computer Monitor User's Manual - UltraScan 4476T.
Download
Page  of 2
4.5, 1937 votes
background image

®

Observe the following safety guidelines when connecting and using your monitor: 

• Be sure your monitor is electrically rated to operate with the AC power available in your location.
• Locate your monitor near an easily accessible electrical outlet.
• Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched with a sharp or abrasive implement.
• Put your monitor in a location with low humidity and a minimum of dust.
• Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep the cable away from where people could trip over it.
• Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
• To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor's case.
• Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
• Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. Also, avoid using the monitor on a bed, 

sofa, rug, or other soft surface. Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some other enclosed space, be 
sure to provide adequate ventilation.

• Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an authorized dealer immediately. You can clean the exterior of 

the monitor with a damp cloth when necessary, but be sure to unplug the monitor first.

• If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or ser-

vice center.

1. Turn off your computer and unplug the computer power cable.
2. Connect the blue connector of the monitor’s signal cable to the blue video connector on the back of your computer. Tighten the connector screws finger tight. Do not 

overtighten. 

3. Fully insert the monitor power cable into the power port on the back of the monitor.
4. Plug the power cables of your computer and your monitor into a nearby electrical outlet.
5. Turn on your computer and monitor. If the monitor does not display an image, refer to the troubleshooting section of this guide.

Use the monitor CD to install the appropriate monitor driver for your operating system.

Microsoft  Windows® 98 Operating System
Windows 98 automatically detects the new monitor and displays the Add New 
Hardware Wizard
 dialog box if the monitor driver is not already installed.

1. Insert the monitor CD in the CD-ROM drive, and click next> twice when the Add 

New Hardware Wizard dialog box appears.

2. Click the CD-ROM drive box to install the drivers from the CD and then click Next>.
3. Confirm that the driver was found on the CD and click Next> twice to install the 

driver.

4. Click Finish to exit the add New Hardware Wizard dialog box.

To manually install or update the driver, perform the following steps:

1. Click Start-> Settings-> Control Panel and then double click Display.
2. In the Display Properties window, click the Settings tab, and then click Advanced
3. Click the Monitor tab, and then click Change.
4. When the Update Device Driver Wizard dialog box appears, follow the steps in the 

previous paragraph.

Microsoft  Windows® 95 Operating System
First determine the Windows 95 version installed on your computer by right-clicking the 
My Computer icon on the desktop and selecting Properties. The version number is 
listed under System. Perform the steps for the appropriate version.

Version 4.00.950A

1. Click Start-> Settings-> Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab and the click Change 

Display Type.

3. In the Change Display Type window, click Change and then click Have Disk.
4. Insert the monitor CD in the CD-ROM drive, type d:\ (change the drive letter to 

match your CD-ROM drive if it is not drive D) in the Copy manufacturer’s files 
from: box, and click OK.

5. In the Select Device window, click the appropriate monitor model and the click OK.
6. In the Change Display Type window, click Close.
7. In the Display Properties window, click OK.

Version 4.00.950B

1. Click Start-> Settings-> Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab and the click Advanced 

Properties.

3. In the Advanced Display Properties window, click the Monitor tab and then click 

Change.

4. In the Select Device window, click Have Disk.
5. Insert the monitor CD in the CD-ROM drive, type d:\ (change the drive letter to 

match you CD-ROM drive if it is not drive D) in the Copy manufacturer’s files from
box, and click OK.

6. In the Select Device window, click the appropriate monitor model and then click OK.
7. In the Advanced Display Properties window, click Close.
8. In the Display Properties window, click OK.

Safety Instructions

Driver Installation

Connecting Your Monitor to a Computer

Dell® Model UltraScan P991 Color Monitor Quick Setup

Related Manuals for Dell UltraScan 4476T

0.549468s