Dell Dell UPS 4200R Owner's Manual

Dell Servers Owner's Manual - Dell UPS 4200R.
Download
Page  of 2
4.7, 1237 votes
background image

w w w . d e l l . c o m   |   s u p p o r t . d e l l . c o m

Attach the rails

NOTE: The instructions are the same for square-hole racks and 
unthreaded, round-hole racks. The rails fi t both rack styles. The 
square-hole rack is shown in the illustration.

1. Select the proper holes in the rail for positioning the cabinet in the  

 

desired location in the rack.

The rails should be located at the bottom of the 2U, 3U, or 4U space    
allocated for the UPS or EBM.

2. Find the end labeled FRONT on both the left and right rails. Position    

each facing inward.

3. Attach the rails to the rack:

Engage the back end of the rail until it fully seats on the vertical rack    
fl ange and the hook latch locks in place.

  Pull the rail toward the front.

Push the front end of the rail until it fully seats on the vertical rack 
fl ange and the hook latch locks in place.

NOTE: Refer to the UPS documentation for installing the UPS in the rack.

Fixez les rails

REMARQUE : Les instructions sont les mêmes pour des baies à trous 
carrés et les baies à trous-ronds non fi letés. Les rails s’adaptent 
aux deux styles de baies. La baie à trous-carrés est montrée sur 
l’illustration.

1. Sélectionnez les bons trous dans le rail pour positionner le module 

à l’emplacement souhaité dans la baie. Les rails doivent être situés 
en bas de l’espace 2U, 3U, ou 4U alloué à l’onduleur ou l’EBM.  
allocated for the UPS or EBM.

2. Trouver l’extrémité marquée AVANT sur les deux rails gauche et 

droite. Positionner chacun d’eux vers l’intérieur.

3. Fixez les rails à la baie :

Emboîtez l’extrémité arrière du rail jusqu’à ce qu’il soit totalement en 
place sur le bord vertical de la baie et que le loquet du crochet soit en 
place.

Tirez le rail vers l’avant.

Poussez l’extrémité avant du rail jusqu’à ce qu’il soit totalement en 
place sur le bord vertical de la baie et que le loquet du crochet soit en 
place.

REMARQUE : Reportez-vous à la documentation de l’onduleur pour 
installer l’onduleur dans la baie.

Anbringen der Schienen

HINWEIS: Für Gestelle mit quadratischen Öffnungen und Gestelle mit 
runden Öffnungen ohne Gewinde gelten die gleichen Anweisungen. Die 
Schienen passen zu beiden Gestellarten. Auf den Abbildungen ist das 
Gestell mit den quadratischen Öffnungen zu sehen.

1. Wählen Sie die korrekten Öffnungen in der Schiene aus, um das 

Gehäuse wie gewünscht im Rack zu positionieren.  

Die Schienen sind im unteren Bereich des für die USV bzw. 
das EBM vorgesehenen 2U-, 3U- oder 4U-Raums anzuordnen.  
allocated for the UPS or EBM.

2. Suchen Sie das Ende mit der Aufschrift FRONT (VORDERSEITE) an 

der linken und rechten Schiene. Richten Sie diese jeweils mit der 
Aufschrift nach innen aus.

3. Bringen Sie die Schienen am Gestell an:

Schieben Sie das hintere Ende der Schiene hinein, bis es vollständig 
auf dem vertikalen Gestellfl ansch sitzt und der Haken einrastet.

  Ziehen Sie die Schiene nach vorne.

Schieben Sie das vordere Ende der Schiene hinein, bis es vollständig 
auf dem vertikalen Gestellfl ansch sitzt und der Haken einrastet.

HINWEIS: Eine Anleitung für den Einbau der USV in das Gestell fi nden 
Sie in der Dokumentation zu der USV.

Прикрепите направляющие

ПРИМЕЧАНИЕ: Инструкции по работе со стойками 
с квадратными отверстиями и стойками с круглыми 
безрезьбовыми-отверстиями одинаковые. Направляющие 
подходят для обоих видов стоек. Стойка с 
квадратными-отверстиями показана на рисунке.

1. Выберите надлежащие отверстия в направляющих для 

размещения корпуса в желаемом месте стойки.  

 

desired location in the rack.

Направляющие должны находиться в нижней части 
зоны 2U, 3U или 4U, выделенной для ИБП или внешнего 
батарейного модуля.

2. На левой и правой направляющих найдите конец с 

обозначением FRONT (лицевая сторона). Расположите 
направляющие лицевой стороной внутрь.

3. Прикрепите направляющие к стойке:

Зацепите задний конец направляющей таким образом, 
чтобы он полностью сел на фланец вертикальной стойки, 
а замок закрылся со щелчком.

Потяните направляющую вперед.

Подтолкните передний конец направляющей таким 
образом, чтобы он полностью сел на фланец вертикальной 
стойки, а защелка защелкнулась.

ПРИМЕЧАНИЕ: Инструкции по установке ИБП на раме 
приведены в документации к ИБП.

Cómo Sujetar los Rieles

NOTA: Las instrucciones son las mismas que para los bastidores de 
orifi cios cuadrados y los bastidores de orifi cios redondos- y sin rosca. 
Los rieles sirven para ambos estilos de bastidores. En las ilustraciones, 
se muestra el bastidor con orifi cios cuadrados.

1. Seleccione los orifi cios adecuados en el riel para posicionar el 

gabinete en la ubicación deseada en el bastidor. 

Los rieles deben ubicarse en la parte inferior del espacio de 2U, 
3U o 4U asignado para el UPS o el Módulo de batería externa.  
allocated for the UPS or EBM.

2. Encuentre el extremo etiquetado FRONTAL en los rieles derecho e 

izquierdo. Coloque cada uno orientado hacia adentro.

3. Conecte los rieles al bastidor:

Acople el extremo posterior del riel hasta que se asiente 
completamente sobre la brida del bastidor vertical y el pestillo del 
gancho se cierre en el lugar.

Tire del riel hacia la parte delantera.

Empuje el extremo delantero del riel hasta que se asiente 
completamente sobre la brida del bastidor vertical y el pestillo del 
gancho se cierre en el lugar.

NOTA: Consulte la documentación del UPS para instalar el UPS en el 
bastidor.

Four-Post Rail Kit 
 Kit de Rail à Quatre Montants | Vierstangiges Schienenset | Комплект из четырех стоек с направляющими  | Juego de Rieles de Cuatro Postes  | 
四柱导轨套件

四柱导轨套件 | 四柱导轨套件

四柱导轨套件 | 

4-Post 레일 키트

4-Post 레일 키트  | ポストレールキット4個

Related Manuals for Dell Dell UPS 4200R

0.515497s