Dacor rsd30 User's Manual | Page 7

Dacor Range User's Manual - rsd30.
Download
Page  of 8
4.2, 2351 votes
background image

Re-installing the Oven door

Grasp the oven door on opposite sides and 

lift it until the door hinges are aligned with the 

openings in the oven frame. Holding the door at 

about a 30˚ angle from the horizontal, slide the 

hinges into the openings until the bottom hinge 

arms drop fully into the hinge receptacles. Lower 

the door to the fully opened position, and then 

rotate the two hinge catches toward the oven. 

Open and close the door completely to ensure 

that it is properly installed. Peel off the protective 

layer of plastic that covers the door panel.

Verifying Proper Gas Operation of 

the dual Fuel Ranges (RSd)

wARNINGS:

1.  The range and shut-off 

valve must be disconnected 

from the gas supply piping 

during any pressure testing 

exceeding 1/2 psi (3.5kPa).

2.  The range must be isolated 

from the gas supply piping 

by closing the shut-off valve 

during any pressure testing at 

or below 1/2 psi (3.5 kPa).

Before beginning the test procedure, ensure 

that all cooktop section control valves are in 

the “OFF” position, and all burner rings, burner 

caps, and grates are properly positioned on the 

top frame. Turn on the gas supply at the shut-off 

valve.

Turn on the power supply to the range. Set the 

time of day by pressing the “CLOCK” key and 

then pressing either of the “TIME•TEMP” keys 

(“+” or “-” keys) to advance or reduce the time in 

the display in the desired setting. 

Test each top burner separately by pressing 

and turning one control knob at a time 

counterclockwise to the “HIGH” position. All 

ignitors will spark continuously, but only the 

burner with gas flowing to it will ignite. It will take 

approximately 4 seconds for ignition to occur, 

at which time the ignitors will stop sparking. If 

ignition does not occur within 4 seconds, turn 

off the knob, wait for at least 2 minutes to allow 

any gas to dissipate, then repeat this ignition 

test. The control knob can then be rotated, 

counterclockwise, from “HIGH” to “LOW” to 

adjust the flame height (size) progressively. 

Repeat the ignition test for all top burners.

When installed properly, the flame will be steady 

and quiet. It will also have a sharp, blue inner 

cone that will vary in length proportional to the 

Verify Proper Operation for Electric 

Ranges (RSE and MRES)

For RSE range top, rotate one surface element 

knob at a time, counterclockwise, to the “HI” 

position. Within 5 seconds, the element should 

be fully energized and glowing red. Verify that 

the residual heat indicator light comes on in 

conjunction with the proper element, within 

approximately 30 seconds. Return the knob 

to the “OFF” position. Repeat for all surface 

elements. (Note: The right front element is  a 

dual coil element. Clockwise rotation from 

“LO” to “HI” will energize the inner coil only. 

Counterclockwise rotation from “LO” to “HI” 

will energize both the inner and outer coils 

together).

For MRES range top, turn an element, tap the 

“ON/OFF” key then tap the slew up/down area 

of the desired element. The element will come 

on at a setting of the number touched and may 

be adjusted up or down by slewing up or down 

on the appropriate key area with your finger. 

To activate the Dual Outer Element, tap the 

circle key at the end of the slew area (second 

row), then tap or slew your finger up or down 

on the second row of numbers. The outer ring 

element will come on at a setting of the number 

touched last. To turn the element off, tap the 

“ON/OFF” key. You may turn off all active 

elements at the same time by tapping twice on 

the “CANCEL•SECURE” key located below the 

controls

NOTE:

when the MRES unit is powered 

on for the first time, the cooktop 

control will go through a self-

check routine. when the self-

check is complete, the cooktop 

control will go to SECURE mode. 

See Use and Care Manual for 

Secure Mode instructions.

Within 5 seconds, the element should be 

fully energized and glowing red. Verify that 

the residual heat indicator light comes on in 

conjunction with the proper element, within 

approximately 30 seconds. 

RSd dual-Fuel Range Control knob

RSE Range Control knob

MRES “SLEw UP/dOwN”  Range Control

NOTES:

If either the oven or cooktop does 

not operate properly, follow these 

troubleshooting steps:
1.  Verify that power (all ranges) 

and gas (RSd) are supplied to 

the range.

2.  Check the electrical 

connections (all ranges) and 

gas (RSd) supply to ensure 

that the installation has been 

completed correctly.

3.  Repeat the above burner 

ignition test (RSd).

4.  If the appliance still does 

not work, contact an 

authorized dACOR service 

company at (800) 772-7778. 

do not attempt to repair the 

appliance yourself. dACOR 

is not responsible for service 

required to correct a faulty 

installation.

CANCEL • SECURE

ON/OFF

ON/OFF

ON/OFF

ON/OFF

NOTE:

Prior to operating the cooktop or 

oven sections of the range, please 

read the accompanying Use and 

Care Manual carefully. Important 

safety, service and warranty 

information is contained within 

this manual.

0.600314s