Craftsman SECURITY + 139.53684 User's Manual

Craftsman Security System User's Manual - SECURITY + 139.53684.
Download
Page  of 2
4.3, 1945 votes
background image

 

Features 

 

For use with any SECURITY

 

✚ compatible

garage door opener receiver.

 

Personalized Password: Up to 10,000
possible combinations. Password can be easily
changed if desired.
Temporary password: Can be added for visitors or service
persons. This temporary password can be limited to a programmable
number of hours or a programmable number of entries.
Rolling Code: While your password remains constant until you
change it, the code between the Keyless Entry and the receiver
changes with each use, randomly accessing over 100 billion new
codes.
Operation: Opener activates when 4-digit password and Enter button
is pressed.
If wrong numbers are accidentally pressed, correction can be made
immediately. The Enter button will transmit only the last four digits.
The Keypad will blink for 15 seconds after the password is
transmitted. During that time the Enter button can be used to stop or
reverse the door travel.
The Lock feature on openers with premium door controls is designed
to prevent operation of the door from portable transmitters.
However, the door will open and close from the door control push
button and the Keyless Entry.

 

To comply with FCC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the password setting and replacing
the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Installation

The recommended
mounting locations for
sectional and one-piece
doors are shown in
Figure 3. You can select
another location if you
prefer. However, the
keypad

must be

installed within sight of
the door.

For a one-piece door,
use the optional location shown in the
illustration (on the 

edge of the door jamb) to avoid injury

as the door swings up and out.

Test the reception of the Keyless Entry by operating your
opener from the selected location. Change the location if
necessary.

Open the keypad and remove the
battery compartment screw and
cover to access the bottom
mounting hole 

(Figure 4).

Center the keypad at eye level
against the selected location. Mark
4 1/4" up the centerline from the
bottom and drill a 1/8" pilot hole.
Install top mounting screw, allowing
1/8" to protrude above surface.
Position keypad on screw head and
adjust for snug fit.

With cover open so bottom
mounting hole is visible, use a punch to
mark hole. Remove keypad and drill 1/8" pilot hole. Replace
keypad and complete installation with bottom screw, using
care to avoid cracking plastic housing. 

Do not overtighten.

Replace the battery cover.

Side two contains instructions for changing the personal
entry password and setting a temporary password.

Door Jamb Edge
(Optional Location 
for 1-Piece Door)

Keypad

Door Jamb Face
SECTIONAL DOOR ONLY

KEYPAD MUST BE INSTALLED 
WITHIN SIGHT OF THE DOOR

Exterior Front Wall
1-Piece or 
Sectional Door

Clavier

LE CLAVIER DOIT ÊTRE POSÉ DE FAÇON

QUE LA PORTE SOIT VISIBLE DU CLAVIER

Mur avant extérieur 

Porte rigide ou articulée

Bordure étroite

 du montant de porte

(emplacement en option

pour les portes rigides)

Face du montant

PORTE ARTICULÉE SEULEMENT

Installation typique

d'une porte articulée

Typical

Sectional Door

installation

Setting the Personal Entry Password

We recommend that you program your password now, before
you install the Keyless Entry. Then you can test  the reception
at the mounting location before you proceed further.

Choose a 4-digit password using the numbers from 0 to 9 (a
number can be used more than once, for example, 4,0, 4,1.)

If you have a Premium Control Console:

1. With the door closed, press the four buttons for

the password, then press and 

hold Enter.

2. Press and hold the light button on the door

control, 

Figure 1.

3. Press and hold the door control push button.

4. After the opener light flashes, release all

buttons.

If you do not have a Premium Control Console:

1. Enter the four digit password desired, then press and 

hold

Enter.

2. Press and release the SRT (learn) button on the door

opener panel, 

Figure 2. 

3. After the opener light flashes, release the Enter button.

Test by pressing your password, then press Enter. The door
should begin to move.

This procedure can be repeated with a different password for
use with a second garage door opener.

The Chamberlain Group, Inc.
Digital Keyless Entry
Replace Battery
7/18/95 - 7/29/96

Battery

Bottom
mounting hole

Battery
Cover

Keypad
Cover

Pile

Trou de
fixation au bas

Couvercle du
compartiment
de la pile

Couvercle
du clavier

The Chamberlain Group, Inc.
Digital Keyless Entry
7/8/95 - 7/27/96

 

SECURITY✚ Garage Door Opener

KG

KG

1

3

9

7

5

1

3

9

7

5

1

2

3

Orange 
SRT (learn)
Button

Yellow 
Indicator
Light

Children operating or playing with a garage door opener can
injure themselves or others. 

The garage door could close and

cause serious injury or death. Do not allow children to operate the
wall push button(s) or remote control(s).
A moving garage door could injure or kill someone under it.
Activate the opener only when you can see the door clearly, it is
free of obstructions, and is properly adjusted.

WARNING

CAUTION

WARNING

AVERTISSEMENT

ATTENTION

AVERTISSEMENT

WARNING

AVERTISSEMENT

1

®

Model 139.53684
Keyless Entry

Figure 2

Figure 1

Figure 3

Figure 4

The Chamberlain Group, Inc.
3 Button Wall Control
Front View
5/1/95

LOCK

LIGHT

Light

Door Control
Push button

Security
Garage Door Opener

Related Manuals for Craftsman SECURITY + 139.53684