Craftsman C3 19.2 Volt Replacement Batteries (2 pk.) Owner's Manual

Craftsman Batteries and Chargers Owner's Manual - C3 19.2 Volt Replacement Batteries (2 pk.).
Download
Page  of 4
4.4, 2472 votes
background image

Battery Packs
Item Nos.

11068 (12 Volt)

11044 (14.4 Volt)

11045 (18 Volt)

11375 (19.2 Volt)

CHARGER SOLD SEPARATELY

Always mention the above item numbers when communi-

cating with us regarding battery packs.
Use battery packs for Craftsman Cordless products only. 

Refer to the Operator’s Manual provided with product.
These battery packs require 1 hour of charging time to be 

fully charged.

Use batteries only with chargers listed.

mODEL nO.

bATTERY PACK

CHARGER

315.110680

130279001

Item No. 9 11068

1425301

Item No. 9 11041

315.110441

130279002

Item No. 9 11044

1425301

Item No. 9 11041

315.110451

130279004

Item No. 9 11045

1425301

Item No. 9 11041

315.113753 130279003, 130279005

Item No. 9 11375

1425301

Item No. 9 11041

batteries vent hydrogen gas and can explode in the 

presence of a source of ignition, such as a pilot light. 

To reduce the risk of serious personal injury, never use 

any cordless product in the presence of open flame. An 

exploded battery can propel debris and chemicals. If 

exposed, flush with water immediately.

Do not charge battery in a damp or wet location. 

 Following this rule will reduce the risk of electric shock.



For best results, your battery should be charged in a 

location where the temperature is more than 50°F but 

less than 100°F. Do not store outside or in vehicles.

Save these instructions. Refer to them frequently 

and use them to instruct others who may use this 

tool. If you loan someone this tool, loan them these in-

structions also to prevent misuse of the product and 

possible injury.

WARnInG! Read all instructions. Failure to follow 

all instructions listed below may result in electric 

shock, fire and/or serious injury. The term “power 

tool” in all of the warnings listed below refers to your 

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool.

Ensure the switch is in the off position before inserting 

battery pack. Inserting the battery pack into power tools 

that have the switch on invites accidents.

Recharge only with the charger specified by the manu-

facturer. A charger that is suitable for one type of battery 

pack may create a risk of fire when used with another bat-

tery pack.

Use power tools only with specifically designated bat-

tery packs. Use of any other battery packs may create a 

risk of injury and fire.

Do not place battery tools or their batteries near fire 

or heat. This will reduce the risk of explosion and possibly 

injury.

  

never use a battery that has been dropped or 

received a sharp blow. A damaged battery is subject to 

explosion. Properly dispose of a dropped or damaged 

battery immediately.

When battery pack is not in use, keep it away from 

other metal objects like paper clips, coins, keys, nails, 

screws, or other small metal objects that can make a 

connection from one terminal to another. Shorting the 

battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from 

the battery, avoid contact. If contact accidentally oc-

curs, flush with water. If liquid contacts eyes, addition-

ally seek medical help. Liquid ejected from the battery 

may cause irritation or burns.

CHARGInG THE bATTERY PACK
Battery packs are shipped in a low charge condition to 

prevent possible problems. Therefore, you should charge it 

until the green LED on the front of the charger comes on.
nOTE: Batteries will not reach full charge the first time they 

are charged. Allow several cycles (operation followed by 
recharging) for them to become fully charged.

CHARGInG A COOL bATTERY PACK
If battery pack is below normal temperature range, the green 

LED on charger will come on. Allow battery pack to reach 

normal temperature, then the red LED will come on.
nOTE: If the charger does not charge the battery pack 

under normal circumstances, return both the battery pack 

and charger to your nearest authorized service center for 

electrical check.

  Charge the battery pack only with the charger  provided.

  Make sure the power supply is normal household  

voltage, 

120 volts, 60 Hz, AC only.

  Connect the charger to the power supply.

  Place the battery pack in the charger aligning raised rib 

on the battery pack with the groove in the  charger.

 See 

Figure 1.

  Press down on the battery pack to be sure contacts on 

the battery pack engage properly with contacts in the 

charger.

  Normally the red LED on charger will come on. This 

indicates the charger is in fast charging mode.

SAFETY RULES

OPERATIOn

Also See for Craftsman C3 19.2 Volt Replacement Batteries (2 pk.)

0.746384s