Craftsman 316.77237 Operator's Manual | Page 6
ASSEMBLY INSTRUCTIONS
HANDLE ASSEMBLY
1.
Remove the nuts and bolts from the middle handle only, but not
the eyehook.
NOTE: DO NOT remove the bolt and nut in the upper handle.
2.
Place the end of the middle handle over the lower handle and
align the holes (Fig. 1). Making sure the “TO START” label is
facing up.
3.
Insert two of the bolts previously removed in step 1 into these holes
and thread the lock-nuts onto them until hand tight.
4.
Using a 3/8” wrench to hold the bolts, tighten the lock-nuts with a
7/16” wrench until firm. DO NOT OVERTIGHTEN.
5.
Place the end of the upper handle onto the end of the middle
handle making sure to align the holes. (Fig. 2)
6.
Insert two of the bolts previously
removed in step 1 into these
holes and thread the lock-nuts
onto them until hand tight.
7.
Repeat step 4 for tightening
of this bolt.
8.
Extend the switch/ throttle
assembly and wires toward
the top of the handle.
9.
Align the switch/ throttle
control assembly post with
the hole that can be found on
the side of the upper handle,
(Fig. 3).
Fig. 1
Lock-Nuts
Bolts
Middle
Handle
Lower
Handle
Fig. 2
Lock-Nuts
Bolts
Upper
Handle
Middle
Handle
10. Firmly push the switch/ throttle assembly onto the upper
handle, making sure that the post slightly protrudes through the
hole on the opposite side.
11. Remove the nut and bolt from the throttle control (Fig. 4).
12. Align the throttle control with the hole on the right side of the
handle.
13. Insert the bolt thru the hole and thread the lock-nut onto it until
hand tight. (Fig. 4).
14. Using a 3/8” wrench to hold the bolt, tighten the lock-nut with a
7/16” wrench until firm. DO NOT OVERTIGHTEN.
15. Cut the Zip tie holding the bail to the handle (Fig. 5).
16. Insert the Z-Hook into the hole on the right side of the bail to
secure the clutch cable to the bail (Fig. 5).
NOTE: Make sure that the bail wire is on top of the upper handle
and not installed under it.
17. Pull out the starter rope and run it thru the eye hook (Fig. 6).
18. Tighten the nut onto the eye hook using a 7/16” wrench to
tighten. DO NOT OVERTIGHTEN.
19. Using the zip ties found in the hardware bag, secure the handle
cables to the lower and middle handle between the eye hook
and the motor housing (see page 5).
Fig. 6
Starter
Rope
Lock-Nut
Eye Hook
Starter Rope Handle
Fig. 4
Bolt
Nut
Throttle
WARNING: DO NOT run any control wires though the
eye hook. As this may prevent certain safety features from
working properly.
Fig. 5
Zip Tie
Z-Hook
Bail
Fig. 3
Post
Switch/
Throttle
Assembly
Upper Handle
6
Related Manuals for Craftsman 316.77237
-
Black & Decker Edger GH710 User's Manual
37 pages
-
Gardena Edger Turbotrimmer 350 L User's Manual
9 pages
-
Black & Decker Edger EDGE HOG LE750 User's Manual
4 pages
-
Black & Decker Edger GH1100 User's Manual
6 pages
-
Black & Decker Edger GH2000 User's Manual
6 pages
-
Black & Decker Edger GH3000 User's Manual
32 pages
-
Black & Decker Edger LE760 User's Manual
7 pages
-
Craftsman Edger 900.79654 User's Manual
11 pages
-
Craftsman Edger 536.7722 User's Manual
24 pages
-
Snapper Edger ET 200 User's Manual
8 pages
-
Snapper Edger ET302B User's Manual
16 pages
-
Troy-Bilt Edger TB22 EC User's Manual
16 pages
-
Troy-Bilt Edger TB415CS User's Manual
44 pages
-
Troy-Bilt Edger TB465SS User's Manual
44 pages
-
Troy-Bilt Edger TBE515 User's Manual
52 pages
-
Troy-Bilt Edger TB22 EC User's Manual
16 pages
-
Echo Edger PE-200 User's Manual
24 pages
-
Homelite Edger F2020 User's Manual
18 pages
-
Black & Decker Edger Black & Decker Edger LE750 User's Manual
7 pages
-
Black & Decker Edger Black & Decker Edger LE750 Type 4 User's Manual
7 pages
-
Black & Decker Edger Black & Decker Edger LST136 User's Manual
48 pages
-
Tanaka Edger TLE-500 User's Manual
20 pages
-
M.E.Y. Equipment Edger ALROH EDGER User's Manual
2 pages
-
STIHL Edger FC 56 C-E Instruction Manual
84 pages