Craftsman 139.53915D User's Manual | Page 31

Craftsman Garage Door Opener User's Manual - 139.53915D.
Download
Page  of 76
4.6, 2421 votes
background image

To Open the Door Manually

DISCONNECT THE TROLLEY:

The door should be fully closed if 
possible. Pull down on the 
emergency release handle (so that 
the trolley release arm snaps into a 
vertical position) and lift the door 
manually. The lockout feature 
prevents the trolley from 
reconnecting automatically, and the 
door can be raised and lowered 
manually as often as necessary.

TO RE-CONNECT THE TROLLEY: 

Pull the emergency release handle 
toward the opener at an angle so 
that the trolley release arm is 
horizontal. The trolley will 
reconnect on the next UP or DOWN 
operation, either manually or by 
using the door control or remote.

To prevent possible SERIOUS INJURY or DEATH from a falling 
garage door:
•   If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or broken 
springs or unbalanced door could result in an open door 
falling rapidly and/or unexpectedly.

•   NEVER use emergency release handle unless garage 

doorway is clear of persons and obstructions.

•   NEVER use handle to pull door open or closed. If rope knot 

becomes untied, you could fall.

Lockout position
(Manual disconnect)

NOTICE

Trolley
Release Arm 
(In Manual
Disconnect
Position)

Trolley

To reconnect

NOT

CE

Emergency
Release Handle
(Down and Back)

Trolley
Release
Arm

Trolley

Using the Wall-Mounted Door Control

THE MOTION DETECTING CONTROL CONSOLE

Press the push bar to open or close the door. Press again to 
reverse the door during the closing cycle or 
to stop the door while it’s opening.

This door control contains a motion detector 
that will automatically turn on the light when 
it detects a person entering the garage. This 
feature can be easily turned off for extended 
work light use.

Light feature

Press the Light button to turn the opener light on or off. It will not 
control the opener lights when the door is in motion. If you turn it 
on and then activate the opener, the light will remain on for 4-1/2 
minutes. Press again to turn it off sooner. The 4-1/2 minute 
interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as 
follows: Press and hold the Lock button until the light blinks 
(about 10 seconds). A single blink indicates that the timer is reset 
to 1-1/2 minutes. Repeat the procedure and the light will blink 
twice, resetting the timer to 2-1/2 minutes. Repeat again for a 
3-1/2 minute interval, etc., up to a maximum of four blinks and 
4-1/2 minutes.

Lock feature

Designed to prevent operation of the door from hand-held remote 
controls. However, the door will open and close from the Door 
Control, the Outdoor Key Switch and the Keyless Entry 
Accessories.

 To activate, press and hold the Lock button for 2 seconds. The 
push button light will flash as long as the Lock feature is on.

To turn off, press and hold the Lock button again for 2 seconds. 
The push button light will stop flashing. The Lock feature will also 
turn off whenever the “learn” button on the motor unit panel is 
activated.

Additional feature when used with the 3-Function hand-held 
remote

To control the opener lights:

In addition to operating the door, you may program the remote to 
operate the lights.

1.  With the door closed, press and hold a 

small remote button that you want to 
control the light.

2.  Press and hold the Light button on the door 

control.

3.  While holding the Light button, press and hold the Lock button 

on the door control.

4.  After the opener lights flash, release all buttons.

LOCK

L GHT

Push 
Bar

Lock
Button

Light
Button

31

Related Manuals for Craftsman 139.53915D

0.495808s