Craftsman 137.21214 User's Manual | Page 4

Craftsman Cordless Saw User's Manual - 137.21214.
Download
Page  of 28
4.1, 2349 votes
background image

 

 

COMPOUND MITER SAW SAFETY 

 
SPECIFIC SAFETY INSTRUCTIONS FOR 
THIS COMPOUND MITER SAW 

 

1.  USE ONLY CROSS-CUTTING SAW BLADES. When 

using carbide tipped blades, make sure they have a 

negative hook angle.   

IMPORTANT: DO NOT USE THIN KERF BLADES

they can deflect and contact guard and can cause 

possible injury to the operator. 

   

2. DO NOT operate the miter saw until it is completely 

assembled and installed according to these 

instructions. 

 

3. IF YOU ARE NOT thoroughly familiar with the 

operation of miter saws, seek guidance from your 

supervisor, instructor, or other qualified person. 

 

4. ALWAYS hold the work firmly against the fence and 

table. DO NOT perform any operation free hand (use 

clamp wherever possible). 

 

5. KEEP HANDS out of the path of the saw blade. If the 

workpiece you are cutting would cause your hands to 

be within 7-1/4” inches of the saw blade, the 

workpiece should be clamped in place before making 

the cut. 

 

6. BE SURE the blade is sharp, runs freely, and is free 

of vibration. 

 

7. ALLOW the motor to come up to full speed before 

starting a cut. 

 
8.  KEEP THE MOTOR AIR SLOTS CLEAN and free of 

chips or dust. 

 

9.  ALWAYS MAKE SURE all handles are tight before 

cutting, even if the table is positioned in one of the 

positive stops. 

 

10. BE  SURE both the blade and the collar are clean and 

the arbor bolt is tightened securely. 

 

11. USE only blade col ars specified for your saw. 

 

12. NEVER use blades larger or smal er in diameter 

than 10-inches. 

 

13. NEVER apply lubricants to the blade when it is 

running. 

 

14. ALWAYS check the blade for cracks or damage 

before operation. Replace a cracked or damaged 

blade immediately. 

 

15. NEVER use blades recommended for operation at 

less than 4800 RPM. 

 

16. ALWAYS keep the blade guards in place and use at 

all times. 

 

17. NEVER reach around the saw blade. 

 

 

18. MAKE  SURE  the blade is not contacting the 

workpiece before the switch is turned ON. 

 

19. IMPORTANT:  After completing the cut, release the 

power switch and wait for the blade to stop before 

returning the saw to the raised position. 

 

20. MAKE  SURE the blade has come to a complete stop 

before removing or securing the workpiece, changing 

the workpiece angle, or changing the angle of the 

blade. 

 

21. NEVER  cut metals or masonry products with this tool.   

This miter saw is designed for use on wood and 

wood-like products. 

 

22. NEVER cut small pieces. If the workpiece being cut 

would cause your hand or fingers to be within 7-1/4” 

inches of the saw blade the workpiece is too small. 

 

23. PROVIDE adequate support to the sides of the saw 

table for long work pieces. 

 

24. NEVER  use the miter saw in an area with flammable 

liquids or gases. 

 

25. NEVER use solvents to clean plastic parts. Solvents 

could possibly dissolve or otherwise damage the 

material. 

 

26. SHUT  OFF  the power before servicing or adjusting 

the tool. 

 

27. DISCONNECT  the saw from the power source and 

clean the machine when finished using. 

 

28. MAKE  SURE  the work area is clean before leaving 

the machine. 

 

29. SHOULD  any part of your miter saw be missing, 

damaged, or fail in any way, or any electrical 

component fail to perform properly, shut off the switch 

and remove the plug from the power supply outlet. 

Replace missing, damaged, or failed parts before 

resuming operation. 

 

ELECTRICAL REQUIREMENTS 

 

POWER SUPPLY AND MOTOR SPECIFICATIONS 
The AC motor used in this saw is a universal, 
nonreversible type. See “MOTOR” in the “PRODUCT 
SPECIFICATIONS” section on page 2. 
To avoid electrical hazards, fire hazards, or damage to 
the tool, use proper circuit protection. Your saw is wired 
at the factory for 120V operation. Connect to a 120V, 15 
Amp circuit and use a 15 amp. time delay fuse or circuit 
breaker. To avoid shock or fire, if power cord is worn or 
cut, or damaged in any way, have it replaced 
immediately

 

 

 

4

0.522735s