Chamberlain 942FP User's Manual

Chamberlain Automobile Electronics User's Manual - 942FP.
Download
Page  of 8
4.3, 1570 votes
background image

®

Model 942FP 

Fingerprint Keyless Entry 

Overview 
The system uses biometric technology that enables an 
authorized user to gain access by scanning their fingerprint. 
The sensor strip on the unit makes a numeric template of the 
fingerprint that is unique to that user. The unit’s memory can 
store up to four fingerprints. 

• The term “enroll” refers to scanning the fingerprint so the 

device will recognize the user. 

• The term “swipe” refers to the movement of the finger across 

the sensor strip. 

• The term “LED” stands for Light Emitting Diode. There are 

6 LEDs located on the Fingerprint Keyless Entry. 

When unit is on, it is programmed to shut off after a short 
period of time. The unit’s sensor strip is sensitive so it is 
important to read the Tips for Success before attempting to 
use the Fingerprint Keyless Entry. 

Carton Inventory 

Receiver 

Fingerprint Keyless 
Entry 

ENROLL

SEND

ENROLL

PASS

FAIL

READY

RETRY

Step 1 Install the Receiver 
1. Unplug the opener before proceeding. 

2. OPEN RECEIVER: Insert a small screwdriver in slot on 

receiver front panel as shown. Twist up actuator cover. 

3. CONNECT RECEIVER AND OPENER: Remove about 1/4" 

(6 mm) of insulation from each end of the 2-strand bell wire. 
Connect one end to the receiver screw terminals (polarity is 
NOT required). Route wire along the channels and out the 
bottom as shown. 

4. Connect the other end of the bell wire to the two opener 

terminals labeled “2” (white) and “1” (red), “common” and 
“command” or the terminals used for the push button control. 

5. Use insulated staples to secure bell wire between receiver 

and opener. Length of bell wire depends on where the 
receiver will be installed. Replace actuator cover. 

6. Choose a 120Vac polarized outlet for the receiver which is 

OUT OF THE REACH OF CHILDREN. Plug receiver into 
selected outlet. Return power to the opener. 

Actuator Cover 

Power Indicator Light 

Terminals 

Bell Wire 
Channels

"SMART" 
Indicator 
Light 

Connect Bell Wire 
To Garage Door 
Opener Terminals 

"SMART" 
Actuator 

Bell Wire

WARNING

WARNING 

To prevent possible SERIOUS INJURY or DEATH from electrocution: 
• Be sure power is not connected BEFORE installing the receiver. 
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• Install Keyless Entry Control within sight of the garage door, out of 

reach of children at a minimum height of 5 feet (1.5 m), and away 
from all moving parts of door. 

• ALWAYS keep remote controls out of reach of children. NEVER 

permit children to operate, or play with remote control
transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly 

adjusted, and there are no obstructions to door travel. 

• ALWAYS keep gate or garage door in sight until completely closed. 

NEVER permit anyone to cross path of moving gate or door. 

NOTICE TO U. S. CONSUMERS: 

Some states prohibit the service or repair of garage door openers which 
cannot be made to comply with the safety standards contained in UL 325 
(1988 revision). In order to comply with both the letter and the spirit of 
these laws, this universal radio control should not be used with any 
LiftMaster®, Chamberlain®, or Sears Craftsman®  garage door opener 
manufactured prior to April 1, 1982. To find out if your Chamberlain-
made garage door opener was manufactured prior to or after April 1, 
1982, please call 1-800-528-9131 before installing this universal radio 
control. 

Step 2 Install the Keyless Entry 
1. Remove cover. 

2. Fasten bottom screw to mounting surface. Allow 1/8" 

(3 mm) to protrude above surface. Position unit on screw 
head and adjust for snug fit. 

3. Fasten top screw. Replace cover. 

Related Manuals for Chamberlain 942FP

0.527667s