Chamberlain 370LMC User's Manual

Chamberlain Universal Remote User's Manual - 370LMC.
Download
Page  of 2
4.1, 1538 votes
background image

Models 370LM/370LMC

3-Button Security

® Mini Remote Control

OWNER'S MANUAL

The 370LM/370LMC Series remote control (Security

®)

works only with door openers and light controls having a
purple “learn” button and a yellow indicator light.

Programming instructions are described and illustrated
below. The additional push buttons can also activate other
315MHz garage door openers and/or light controls.
(Instructions for programming light products are included
with those accessories.)

KG

1

3

9

7

5

KG

1

3

9

7

5

1. Press and release the “learn” button on

the motor unit. The learn indicator light
will glow steadily for 30 seconds.

2. Within 30 seconds, press and hold the 

button on the hand-held remote. 

3. Release the button when the motor unit

light blinks. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.

To Erase All Codes From Motor Unit Memory

To deactivate any unwanted remote, first erase all codes:

Press and hold the “learn” button on motor unit until the learn
indicator light goes out (approximately
6 seconds). All previous codes are now
erased. Reprogram each remote or keyless
entry you wish to use.

To Control the Opener Lights

With SECURITY

✚® transmitters, a remote push button can 

be programmed to operate the opener lights without opening 
the door.

1. With the door closed, press and hold the remote button that

you want to control the light.

2. Press and hold the Light button on the door control.

3. Press and hold the Lock button on the door control.

4. After the opener lights flash, release all buttons.

Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.

Instructions are Described and Illustrated Below

Open/Close/Stop Operation 
(Only if you have a Multifunction door control)

Your Security

✚® remote control can be programmed to operate

one door using all 3 buttons: the left button will only open the
door, the middle button will only close the door, and the third
button will stop the door’s movement. You may set up this 
feature as follows:

1. With the door closed, press and hold the

left remote push button.

2. Press and hold the Lock button on the

door control.

3. Press and hold the door control push bar.

When the opener lights flash, release all buttons. Test by 
pressing the left (Open) button on the remote. The door should
open. Press it again while the door is open and nothing should
happen. Press the middle (Close) button and the door should
close. Press the third (Stop) button while the door is moving
and it should stop immediately.

To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children.  NEVER 

permit children to operate, or play with remote control 
transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

WARNING

CAUTION

WARNING

WARNING

The Remote Control Batteries

The lithium batteries should
produce power for up to
5 years. To replace, pry open
case as shown. Insert 
batteries positive side up (+).

Dispose of old batteries 
properly.

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

WARNING

CAUTION

WARNING

WARNING

Open

Close

Stop

© 2006, The Chamberlain Group, Inc.

114A3091C

All Rights Reserved

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

LiftM

ast

er

Related Manuals for Chamberlain 370LMC

0.502282s