Casio Casio Watch 2301 User's Manual

Casio Watches User's Manual - Casio Watch 2301.
Download
Page  of 2
4.3, 1371 votes
background image

1798/2301-1

Module No.1798/2301

GENERAL GUIDE

• Press C to change from mode to mode.

• Holding down C for a few seconds in any mode enters the Stopwatch Mode.  Holding down C in the Stopwatch Mode changes to the Timekeeping Mode.

• There are two stopwatches in the Stopwatch Mode. Press C while in the Stopwatch Mode to toggle between them. See “STOPWATCH MODE” for more information.

• At any time except while making settings,  press D to illuminate the display for about 4 seconds.

TIMEKEEPING MODE

• In the Timekeeping Mode, press B to switch between the 12-hour and 24-hour

formats.

To set the time and date

1. Hold down A until the seconds digits start to flash.
2. Press  C to move the selection around the display in

the following sequence.

Seconds

Hour

Minutes

Day

Year

Month

3. While the seconds digits are selected (flashing), press D to reset the seconds to

00. If you press D while the seconds count is in the range of 30 to 59, they are
reset to 00 and 1 is added to the minutes. If the seconds count is in the range of 00
to 29, the minutes count is unchanged.

4. While any other digits (besides seconds), are selected (flashing), press D to in-

crease the number or B to decrease it. Holding down either button changes the
digits at high speed.

• The date can be set with the range of January 1,1995 to December 31, 2039.
5. After you are set the time and date, press A to return to the Timekeeping Mode.

• The day of the week is automatically set in accordance with the date.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode automatically.

• When the time shown on the display does not match the analog setting, see

“H-SET MODE” to correct the analog setting.

ABOUT THE BACKLIGHT

• Hold down D to illuminate the display for about 4 seconds. The backlight is dis-

abled while an input screen (with a flashing setting) is on the display.

• The backlight of this watch employs an electro-luminescent (EL) light, which loses

its illuminating power after very long term use.

• Frequent use of the backlight shortens the battery life.

• The watch emits an audible sound whenever the display is illuminated. This does

not indicate malfunction of the watch.

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The backlight automatically turns off whenever an alarm sounds.

STOPWATCH MODE

The Stopwatch Mode automatically saves the best five lap times in memory, along
with lap numbers. You can later recall the saved data using the “RESULT MODE”.
The Stopwatch Mode provides you with the following types of stopwatch capabilities.
Single Stopwatch

This is a standard stopwatch that measures elapsed time and lap times.

Dual Stopwatch

This stopwatch lets you measures the times of two cars or runners at the same
time.

Selecting the Stopwatch Type
While in the Stopwatch Mode, press C to toggle between the Single Stopwatch and
Dual Stopwatch. Note that the C button is disabled while a stopwatch timing opera-
tion is in progress.
Depending on your watch model, the stopwatch display indicators may show CAR1
and CAR2 or STW1 and STW2.

Single Stopwatch

Dual Stopwatch

Stopwatch type
indicator

Single Stopwatch
The Single Stopwatch is a standard stopwatch that measures elapsed time and lap
times.

Lap time

Total time

Hours

Minutes

Seconds

Minutes

Seconds

1/100 Second

To measure elapsed time with the Single Stopwatch
1. Press B to start timing.
2. Press B again to stop timing.
You can repeat steps 1 and 2 as many times as you like.
3. Pressing A while timing is stopped resets the display to all zeros.

To measure lap times with the Single Stopwatch
1. Press B to start timing.
2. Pressing  A while an timing operation is in progress displays the lap time in the

upper part of the display and the lap number in the lower part. This information
remains displayed for about four seconds, after which the elapsed time display
returns.

You can repeat step 2 as many times as you like.
3. Press B to stop timing.
4. Pressing A while timing is stopped resets the display to all zeros.

• The final time on the display when you press B to stop timing is not stored into

memory as a lap time. If you want to save the final time, press A and then B.

Dual Stopwatch
Use the Dual Stopwatch to measure the times of two cars or runners at the same
time. You can also produce lap times for both and determine the difference between
them.

• The Dual Stopwatch is designed to time two runners or cars starting or passing at

different times. Accurate measurement is not possible when both start or pass at
the same time or close to the same time.

To use the Dual Stopwatch
1. Press B to start timing of the first starter, which appears in the upper part of the

display.

2. Press A to start timing of the second starter, which appears in the lower part of the

display.

3. When the first starter passes the timing points, press B.
4. When the second starter passes the timing points, press A.

• The difference between the two times appears on the display for about four sec-

onds. After that, each lap time appears for about four seconds.

• If the time of the second starter is faster than that of the first, the time difference is

displayed as a negative value.

• If the time difference is 10 minutes or more, -- -- -- is displayed in place of the time.

• If the times being compared are from different laps, the time difference is shown

without a plus or minus indication.

• Hold down A or B to stop timing. The final time on the display when you hold down

A or  B to stop timing is not stored into memory as a lap time. If you want to save
the final time, press A or B, and then hold down A or B to stop timing.

RESULT MODE

Use this mode to view the best five lap times and lap numbers. Lap times are stored
by either a Single Stopwatch or Dual Stopwatch operation. Current memory contents
are always the results produced by the last stopwatch operation.
If you know the length of a lap, you can input it and calculate the speed as well. You
can input or change the length either before or after the timing operation.

To input the length of a lap
1. Hold down A until the kilometers digits start to flash on the display
2. Each press of C moves the input position between the kilometers digits and the

decimal digits.

3. After inputting the value you want, press A to save it.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Result Mode automatically.

Result Mode

Timekeeping

Mode

H-SET Mode

Single

Stopwatch

Dual Time Mode

Alarm Mode

Dual

Stopwatch

Stopwatch Mode

Month Day

Day of
week

Hour

Minutes

Seconds

PM
indicator

Lap time

(second starter)

Start/Lap

(second starter)

Start/Lap
(first starter)

Lap time
(first starter)

Minutes

Seconds

1/100 Second

0.623964s