Casio casio 5142 User's Manual

Casio Watches User's Manual - casio 5142.
Download
Page  of 12
4.4, 2036 votes
background image

Operation Guide 5142

E-9

 While crown button mode switching is disabled, pressing the crown button will 

 

x

cause the 

Second Hand to move to the 3 o’clock position. The x Second Hand 

will resume normal timekeeping when you release the crown button.

To re-enable crown button mode switching
Hold down the crown button as you press 

A.

E-8

Note

 If you do not perform any operation for more than three minutes after pulling out the 

 

x

crown, crown operations will become disabled automatically. If this happens, push 
the crown back in and then pull it out again to re-enable crown operations.

Disabling Crown Button Mode Switching
You can use the following operation to disable crown button mode switching. 
This helps to prevent accidental mode changes while wearing the watch.

To disable crown button mode switching

 Hold down the crown button for at least two seconds until the watch beeps and 

1. 

then press 

A.

At this time the 

 

x

Second Hand will move to the 3 o’clock position.

Release both buttons.

2. 

The watch will return to normal timekeeping.

 

x

E-7

Note

 You can use high-speed hand movement when confi guring time settings in the 

 

x

Timekeeping Mode, Alarm Mode, or Countdown Timer Mode, or when adjusting the 
home positions of the hands.

Pushing the Crown In

Carefully press the button of the crown the push the crown back in.

Important!

 To prevent unintentional operation, the button press operation of the crown 

 

x

becomes disabled automatically for about eight seconds after you push the crown 
back in. It will become re-enabled after about eight seconds.

E-6

High-speed 1

With the crown pulled out, rotate it rapidly away from you two times.

High-speed 2

After starting the High-speed 1 operation, rotate the crown rapidly 
away from you two more times.

High-speed Cancel

Rotate the crown towards you or press any button.

E-5

Pulling the Crown Out

After unlocking the crown, grasp the ring and pull the crown out.

Rotating the Crown

With the crown pulled out, grasp the ring and rotate the crown 
towards you to move the hands of the watch.
You can also perform high-speed hand movement using the 
operations described below. Note that there are two levels of high-
speed movement (High-speed 2 is faster).

 Use High-speed 2 when changing the minute hand setting in the 

 

x

Timekeeping Mode, Timer Mode, and Alarm Mode.

E-4

 Note that rotating the ring without pushing it down as far as it will go will change the 

 

x

settings of the watch. When locking the crown, be sure to press down fi rmly on the 
ring as you rotate it.

Unlocking the Crown

Rotate the ring part of the crown towards you until it loosens 
completely.

Pressing the Crown Button

You can press the crown button while the crown is locked.

Crown ring

Press

E-3

Using the Crown

The crown of this watch has a button part and a ring part. You can use the crown’s 
button and ring to perform a number of different crown operations.

Locking the Crown

To lock the crown, push down its ring part as far as it will go as you 
rotate the ring away from you until it is relatively tight. While the 
crown is locked correctly, the only crown operations possible are 
pressing the crown button and unlocking the crown.

Important!

 Push down on the ring as you slowly rotate it. You should be able to feel it screwing 

 

x

securely into place.
 You should normally have the crown locked during normal daily use. Leaving the 

 

x

crown unlocked creates the risk of unintended operations or even damage due to 
impact.

E-2

About This Manual

In this manual, operations are performed using the watch’s 
crown, and the three buttons indicated by the letters 

A, 

B and C.

Hands and Indicators
z  Hour Hand

x  Second Hand

c  Minute Hand

v  Mode Disk:  Rotates to indicate the current mode and 

other information.

b  Chronograph Signal

n  Day
This User’s Guide uses numbers shown above to identify 
watch hands and indicators.

+

6

*

>

@

B

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

 Note that the product illustrations in this manual are intended for reference only, and so 

 

x

the actual product may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5 
hours. Because of this, the radio-controlled atomic timekeeping function will not 
display the correct time for Newfoundland, Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any 
damage or loss suffered by you or any third party arising through the use of this 
product or its malfunction.

MA1203-EB

0.574831s