Carvin AC175 Owner's Manual

Carvin Musical Instruments Owner's Manual - AC175.
Download
Page  of 1
4.9, 1626 votes
background image

STRINGS

Your Carvin guitar is equipped with a high quality 

set  of  Carvin    strings.    For  replacement  strings, 

please order from our catalog.  If you change to 

considerably  lighter  or  heavier  strings,  you  may 

need to adjust the truss rod in the neck to maintain 

good string action.  For long string life, keep the 

strings clean with a soft dry cloth.  Replace strings 

regularly  to  avoid  dead  strings  which  can  cause 

intonation problems.

2-WAY TRUSS ROD ADJUSTMENT 

    Carvin  guitars  come  with  a  2-way  adjustable 

truss rod, allowing you to add the proper amount 

of forward bow, even to a neck with an excessive 

reverse bow condition.  You can check the neck 

yourself  for  the  proper  amount  of  forward  bow.  

You will need a straightedge about 18” long and 

a feeler gauge set.  Tune the guitar to the proper 

pitch  and  place  the  straightedge  edgewise  on 

the center of the fingerboard so that it is resting 

on  the  first  and  last  fret.    Now  take  the  feeler 

gauge set and check for clearance at the 7th fret. 

Viewing  from  the  tip  of  the  headstock  (with  the 

frets  facing  away  from  you),  the  truss  rod  nut 

must be turned left (counter clockwise) if there is 

less than .005” clearance at the 7th fret. If more 

than .015” clearance, the truss rod nut must be 

turned clockwise.  The optimum forward bow is 

.010”.    Turning  the  nut  to  the  right  (clockwise) 

will reduce the amount of forward bow.  To make 

adjustments  use  the  4mm  hex  wrench  provided 

with  your  guitar.    A  5/32”  hex  wrench  wil   also 

work. Turn the nut 1/10 of a turn and recheck. Do 

Not force or over tighten the truss rod!

    Note:  If  you  have  just  received  your  Carvin 

guitar  and  the  string  action  is  very  low  with 

buzzing  frets,  then  chances  are  the  neck  needs 

adjusting  because  of  a  backbowed  condition 

sometimes  caused  during  shipping.    If  this  is 

the  case  then  remove  the  truss  rod  cover  with 

a small phillips screwdriver.  Turn the truss rod 

counter  clockwise  until  you  have  .010”  forward 

bow.    This  is  about  the  thickness  of  a  playing 

card.

  If you don’t have a straightedge or feeler gauge 

set, you can achieve great results by pressing one 

of your outside strings down at the first fret and 

24th fret and having a friend slide a playing card 

between the 7th fret and the bottom of the string.  

The  card  should  slide  under  without  lifting  the 

string up.  Adjust the truss rod accordingly.

CHANGING STRINGS WITH SPERZELS

• Loosen strings completely by turning the tuning 

buttons on the Sperzel machine heads.

•  Loosen  the  string  lock  thumb  screws  counter 

clockwise  on  the  back  of  the  Sperzel  gears.  

You  only  need  to  turn  theses  screws  about  2 

or 3 turns.

• To remove strings, pull strings out of the string 

post holes.

• To install strings, slide string through the small 

hole  in  the  Sperzel  string  post.    Take  up  all 

the slack then tighten the thumb screw on the 

back.  Cut off the excess string and then tune 

your guitar.

• 

Stretch  your  new  strings  by  pul ing  sideways 

on them fairly hard and retune.

TIPS FOR SPERZEL TUNERS

• If your guitar has a tremolo, don’t rest palm on 

tremolo while tuning.

• When stringing up Sperzel tuners, do not wrap 

multiple string wraps around the post.  Eliminate 

as many wraps as possible to keep your guitar 

in better tune.  3/4 of one turn around the string 

post should be considered maximum.

• You can adjust the tension of the Sperzel tuning 

keys with a small slot head screwdriver.  Just 

tighten  or  loosen  the  screw  on  the  end  of  the 

button until the desired tension is obtained.  To 

eliminate any backlash, adjust the buttons fairly 

tight.  This will give your tuning buttons a more 

secure  feel,  and  wil   not  hurt  the  longevity  of 

the internal gears.

BRIDGE HIGHT ADJUSTMENT

      Each  Carvin  guitar  is  set  for  best  possible 

playing action for the average guitarist.  Guitarists 

with  a  light  playing  style  can  possibly  lower  the 

action slightly.  All guitarists with a hard playing 

style  will  probably  have  to  raise  the  action 

slightly. 

FT6 Hardtail Bridge: Each saddle can be adjusted 

individually for height with a 1.5mm hex wrench.

M-style  Tune-O-Matic  bridge:  Adjust  the 

bridge  height  with  the  proper  size  screwdriver. 

Recomended slot size .250 wide x .055 wide.

ADJUSTING INTONATION

  Use your guitar tuner to fine tune your intonation.  

With  the  aid  of  your  electronic  tuner,  tune  each 

string to the proper pitch.  Now check your high 

E string tuning at the 12th fret.  If the tuner shows 

sharp, then adjust the high E bridge saddle slightly 

further  away  from  the  neck.    If  the  tuner  shows 

flat,  adjust  the  saddle  towards  the  neck.    Try 

moving the saddle  1/32” (about the thickness of 

a dime).  Retune the open E string perfectly and 

recheck the octave tuning at the 12th fret.  If the 

tuning is perfect, you are done intonating the high 

E string.  If it is stil  sharp, then keep moving the 

string saddle further away from the neck until your 

intonation  is  perfect.    Repeat  this  procedure  for 

each string.  Use a #1 phil ips screwdriver.

ADJUSTING PICKUP HEIGHT

  Each pickup has 2 or 3 height adjusting screws.  

For  maximum  power  output  keep  the  pickups 

adjusted  as  close  to  the  strings  as  possible 

while  maintaining  enough  clearance  so  that  the 

pickup  pole  pieces  will  not  touch  the  strings 

when  playing  on  the  upper  frets.    If  you  want  a 

mellower sound, then adjust the pickups further 

away from the strings.  For humbucking pickups 

we  recommend  5/32”  clearance.    For  single  coil 

pickups go with 1/8” clearance. 

ADJUSTING INDIVIDUAL PICKUP POLES

    We  set  each  magnetic  screw  head  in  both 

pickups for a balanced sound.  If you wish to raise 

or lower the output of a certain string, then lower 

or raise the adjustable screw heads until you get 

the  desired  power  output  of  that  string.    Press 

strings down on the 24th fret and make sure that 

you  have  at  least  1/16”  clearance  between  the 

strings  and  the  pickup  screw  heads,  otherwise 

you may get static as a result.  Keep the pickup 

pole  pieces  clean  as  any  metallic  particles  on 

them can cause static.

CLEANING AND POLISHING

  

 For  al  Carvin guitars  with a gloss finish, use  

any good quality automobile wax or guitar polish.  

To  avoid  scratching  the  finish  use  a  clean  soft 

cloth.  Do not get wax on the ebony fingerboard.

    For  Carvin  guitars  with  the  natural  tung  oil 

finish,  apply  a  good  furniture  oil  such  as  “Old 

English” lemon oil and wipe off the excess.  This 

should be done at least twice a year.

    The  ebony  fingerboard  should  also  be  oiled 

with  lemon  oil  twice  a  year.    Do  this  while  the 

strings  are  off  the  guitar.    The  oil  wil   prevent 

the fingerboard from receiving or loosing excess 

moisture,  which may cause the wood to crack.

WARNING

•  Your  guitar  is  constructed  of  solid  wood  that 

was  seasoned  and  dried  to  specific  moisture 

requirements.

• If you live in a desert, high mountain or a cold 

winter  region,  you  will  experience  dry  and 

extreme weather conditions from time to time, 

which can crack your fingerboard and in severe 

cases, crack other parts of your guitar and the 

finish.  You can prevent cracking by storing your 

guitar  in  it’s  case  and  by  not  subjecting  it  to 

extreme heat or cold.

•  If  you  live  in  humid  regions  such  as  the 

Southeastern United States, or near the ocean, 

you  should  take  extra  precautions  and  keep 

your instrument in its case or gig bag as much 

as possible.

•  Do  not  leave  your  guitar  and  case  in  direct 

sunlight or in your car when it is hot. Heat inside 

a  car’s  trunk  can  exceed  130˚.  Heat  build-up 

inside the case can become intense and damage 

the instrument.

•  When  the  instrument  is  not  in  use  or  when 

shipping,  do  not  release  the  tension  of  the 

strings, as this is harmful to the neck and may 

cause an irreversible backbow.

• Carvin does not warranty cracks or neck warpage 

due  to  extreme  weather  conditions,  improper 

storage or misuse.

MAINTENANCE AND ADJUSTMENT PROCEDURES FOR CARVIN GUITARS

Locking

Thumb Screw

Loosen

Tension 

Adjustment

String Post

76-00004C  0808

c

0.533929s