Carrier WEATHERMAKER 8000 58ZAV Instruction Manual | Page 2

Carrier Furnace Instruction Manual - WEATHERMAKER 8000 58ZAV.
Download
Page  of 24
4.4, 1393 votes
background image

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

PROCEDURE

Electrostatic discharge can affect electronic components.
Take precautions during furnace installation and servicing to
protect the furnace electronic control. Precautions will pre-
vent electrostatic discharges from personnel and hand tools
which are held during the procedure. These precautions will
help to avoid exposing the control to electrostatic discharge
by putting the furnace, the control, and the person at the same
electrostatic potential.

1. Disconnect all power to the furnace. DO NOT TOUCH THE

CONTROL OR ANY WIRE CONNECTED TO THE CON-
TROL PRIOR TO DISCHARGING YOUR BODY’S ELEC-
TROSTATIC CHARGE TO GROUND.

2. Firmly touch a clean, unpainted, metal surface of the furnace

chassis which is close to the control. Tools held in a person’s
hand during grounding will be satisfactorily discharged.

3. After touching the chassis you may proceed to service the

control or connecting wires as long as you do nothing that
recharges your body with static electricity (for example; DO
NOT move or shuffle your feet, DO NOT touch ungrounded
objects, etc.).

4. If you touch ungrounded objects (recharge your body with

static electricity), firmly touch furnace again before touching
control or wires.

5. Use this procedure for installed and uninstalled (ungrounded)

furnaces.

6. Before removing a new control from its container, discharge

your body’s electrostatic charge to ground to protect the
control from damage. If the control is to be installed in a
furnace, follow items 1 through 5 before bringing the control
or yourself into contact with the furnace. Put all used AND
new controls into containers before touching ungrounded
objects.

7. An ESD service kit (available from commercial sources) may

also be used to prevent ESD damage.

Table 1—Dimensions (In.)

UNIT SIZE

A

D

E

VENT CONN

SHIP. WT (LB)

050-08

14-3/16

12-9/16

12-11/16

4

124

050-12

14-3/16

12-9/16

12-11/16

4

128

070-08

14-3/16

12-9/16

12-11/16

4

129

070-12

14-3/16

12-9/16

12-11/16

4

137

096-12

17-1/2

15-7/8

16

4

146

096-16

17-1/2

15-7/8

16

4

151

115-16

17-1/2

15-7/8

16

4

159

115-20

21

19-3/8

19-1/2

4

174

115-22

21

19-3/8

19-1/2

4

176

135-20

24-1/2

22-7/8

23

5

193

Fig. 1—Dimensional Drawing

A99288

4 3⁄16″

2″

2 15⁄16″

13⁄16″

11⁄16″

9 1⁄8″

10 1⁄4″

1 1⁄16″

2 1⁄8″

8 1⁄4″

10 1⁄4″

1 1⁄16″

2 1⁄8″

16 1⁄16″

13 5 ⁄16″

19″

11⁄16″

13⁄16″

11⁄16″

20″

28 1⁄2″

39 7⁄8″

D

5⁄8″ TYP

1″ TYP

E

A

AIRFLOW

OUTLET

INLET

1⁄2″ DIA

THERMOSTAT

WIRE ENTRY

7⁄8″ DIA

ACCESSORY

7⁄8″ DIA

ACCESSORY

DIMPLES TO DRILL HOLES

FOR HANGER BOLTS (4 PLACES)

IN HORIZONTAL POSITION

ADDITIONAL 7⁄8″ DIA K.O.’s ARE

LOCATED IN THE TOP PLATE

AND BOTTOM PLATE

NOTE:

7⁄8″ DIA HOLE

POWER ENTRY

1 1⁄2″ DIA

R.H. GAS ENTRY

7⁄8″ DIA

ACCESSORY

1 3⁄4″ DIA HOLE

GAS ENTRY

VENT CONNECTION

Minimum return-air openings at furnace, based on metal duct.  If flex duct is used,

see flex duct manufacturer's recommendations for equivalent diameters.

     a.  For 800 CFM–16-in. round or 141⁄2 x 12-in. rectangle.

     b.  For 1200 CFM–20-in. round or 141⁄2 x 191⁄2-in. rectangle.

     c.  For 1600 CFM–22-in. round or 141⁄2 x 231⁄4-in. rectangle.

     d.  For airflow requirements above 1800 CFM, must use entire return air opening.

NOTE:

2

 

Also See for Carrier WEATHERMAKER 8000 58ZAV

0.542442s