Canon PIXMA mini320 Instruction Guide

Canon Printers and Multifunction Instruction Guide - PIXMA mini320.
Download
Page  of 2
4.9, 1861 votes
background image

Start Here

Easy Setup Instructions

Photo Printer

1PreparethePrinter
a

UnpackthePrinter.

Confirm the included items against the illustration printed on the lid of the 

packing box.

A USB cable is necessary to connect the printer with your computer.

b

 Place the printer on a flat and horizontal surface, and do not 

place any objects in front of the printer.

Remove all the shipping tapes.

c

 Connect the power cord to the AC adapter. Plug the AC 

adapter into the printer, and connect the other end of the 

power cord to a power outlet. Then press the Open button to 

open the Paper Feed Tray and the Paper Output Tray.

Open button

d

 Open the Paper Feed Tray and fold it in half. Then press the 

ON/OFF button.

The Language selection screen will be displayed.

The Paper Output Tray 

will open automatically.

Paper Feed Tray

ON/OFF button

Important

IftheAlarmlampislitorangeandanerrormessageisdisplayed,see“Error

MessageIsDisplayedontheLCD”intheDirect Photo Guide.

e

 Use the {or} button or the 

Easy-ScrollWheelonthe

Operation Panel to select the language for the LCD, then 

press the 

OK button.

Easy-Scroll Wheel

Important

IfanunintendedlanguageisdisplayedontheLCD,presstheBackbuttonto

returntotheLanguageselectionscreen.

f

 Write down the serial number located on the bottom face of the 

printer. You will need this to register your product.

Serial Number

2Installtheinktank

d

 Insert the ink tank at a slant.

Align the mark ▲ on the ink tank and 

the mark ▼ on the printer.

e

 Press the   mark on the ink tank until it clicks into place and 

then its lamp lights red.

Caution

Ifthefront(innermost)partoftheinktank(A)isstickingup,pushdownonthe

Canonlogoontheinktankasillustratedbelow.Donotremovetheinktank

forcibly.

(A)

Important

Ifthelampdoesnotlightredafteritisinserted,repeatstepsdande.

f

 Open the Printer Cover slightly, pull the Lock Lever to unlock, 

and then close the Printer Cover.

Lock Lever

Important

Theprinterstartsoperating.Waitabout1minuteuntiltheprinterstopsmaking

operatingnoises.

Note

An error message will be displayed on the LCD if the Print Head Lock Lever is not 

set properly or the ink tank is not installed properly. Open the Printer Cover and make 

sure that the lock lever is set properly and ink tank is installed properly.

Note

For the ink tank compatible with this printer, refer to the back cover of the Direct Photo 

Guide.

a

 Slide the Lock Switch to the right.

b

 Hold the Lock Switch in position, and lift the Printer Cover.

The cover will be locked if it is fully lifted.

The procedure for installing the ink tank is displayed on the LCD.

Printer Cover

The Print Head Holder moves to the center of the printer. 

Install the ink tank here.

Important

IfthePrinterCoverisleftopenformorethan10minutes,thePrintHeadHolder

movestotheright.CloseandreopenthePrinterCovertoreturntheholderto

thecenter.

c

 Remove the orange protective cap and discard it.

Protective Cap

Ink Ports

Electrical Contacts

Important

Donottouchtheelectricalcontactsortheinkports.

Donotreattachtheprotectivecaponceyouhaveremovedit.

Important

Whencleaningtheexterioroftheprinter,useasoftclothtowipeitgently.Fordetails,referto“CleaningYourPrinter”intheUser’s Guideon-screenmanual.

3AlignthePrintHead

a

 Load a sheet of the 

SUPPLIED 5" x 7" / 127.0 x 177.8 mm 

paper into the Rear Tray with the printing side (whiter side) 

facing front. Align the paper with the right side of the Rear 

Tray, then slide the Paper Guide toward the left edge of the 

paper.

Rear Tray

Paper Guide

Align the right side.

5" x 7" / 127.0 x 177.8 mm

b

When the message requesting head alignment is displayed on 

the LCD, press the 

OK button.

A pattern is printed and the Print Head is aligned automatically.

Note

The pattern is printed in black and blue only.

Automatic Print Head Alignment will take about 4 minutes to complete. Do not start 

another operation until the printer has stopped making operating noises.

If Automatic Print Head Alignment cannot be executed correctly and a message is 

displayed on the LCD, please refer to “Error Message Is Displayed on the LCD” in 

theDirect Photo Guide.

HardwaresetupandPrintHeadalignmentiscomplete.
Ifyouareconnectingtheprintertoacomputer,pleaseseethebacksideof
thissheetforSoftwareInstallationInstructions.

Related Manuals for Canon PIXMA mini320

0.630958s