Brother XL5060NTC User's Manual
Step 3
Winding the bobbin. (Your machine may be supplied with a fully wound
bobbin, but you may want to fill another bobbin with your own thread.)
Step 4
Lower threading. (Your machine may be supplied with a threaded bobbin,
but you may want to use another bobbin with your own thread.)
•
Set the power switch to on (I).
Place a spool of thread on the spool pin (figure 3a).
Unwind some thread and pass the thread around the
tension disk.
•
Take one of the bobbins from the accessory pack.
•
Pass the thread through the hole in the bobbin from
the inside.
Clip the bobbin onto the bobbin winding shaft.
Push the bobbin winding shaft firmly to the right until
it clicks into place against the stop (figure 3b).
•
Hold the end of the thread and press the foot controller
to wind the thread around the bobbin a few times.
Trim the excess thread (figure 3c), and continue
winding until the winding shaft stops automatically.
•
Push the bobbin winding shaft back to the left, cut the
thread, and remove the bobbin from the shaft (figure 3d).
Unwind the thread from the tension disk.
•
Set the power switch to off (O).
Raise the needle to its highest position by turning the balance wheel towards you (counter-clockwise).
Open the shuttle cover behind the extension table.
•
Hold the bobbin case in your left hand with the
bobbin case finger pointing towards you (figure 4c).
With your right hand, pull the trailing thread into the
slot in the bobbin case (figure 4c).
•
Draw the thread down under the spring into the
delivery eye (figure 4d).
•
Hold the bobbin case by the latch, with the finger
pointing upwards (figure 4e).
Insert the bobbin back into the shuttle, release the
latch, and push the bobbin in until it clicks.
Make sure the bobbin case goes in all the way, or the
latch will not hold the bobbin properly.
Leave the shuttle cover open.
delivery
eye
bobbin
case
finger
spring
tension
disk
slot
latch
•
Remove the bobbin case from the shuttle, by pulling
the latch (marked in red on figure 4a).
•
Leaving about 10 cm (4 in) of thread trailing, insert
the bobbin into the bobbin case (figure 4b).
figure 3a
figure 3b
figure 4a
figure 4b
figure 4c
figure 4d
figure 4e
figure 3c
figure 3d
GETTING STARTED:
XL series Sewing Machines
XL5050NTC
XL5060NTC
XL5070NTC
To help you get started, please follow these simple instructions in the order shown below.
However, before you do so, read the safety instructions in the Instruction Manual.
Step 1
Unpack the sewing machine, and familiarise yourself with all the parts
and controls that are mentioned in these instructions.
Step 2
Prepare the sewing machine for use.
Foot
Controller
Mains
Plug
Power
Switch
Balance
Wheel
Foot
Controller
Connection
Bobbin Winding
Shaft
Stitch
Length
Dial
Pattern
Dial
Reverse
Lever
Take-up
Lever
Guide
Thread
Cutter
Presser Foot and
Needle Assembly
Presser Foot
Lever
Extension Table
(accessories and
bobbins inside)
Shuttle
Cover
Spool Pin
Tension
Dial
Tension Disk and
Thread Guide
Figure 1a
Figure 1b
Bobbin and
Bobbin Case
•
Plug in the foot controller connector at the right hand side of the machine, as shown in figure 1a. Connect the
mains plug into a wall socket, and place the controller on the floor.
Grip the top of the spool pin, and pull it upwards as shown in figure 1b until it clicks into place at a height of
about 50 mm (2 in). Be careful not to pull the pin off the machine.
Set the tension dial to 5.
Set the pattern dial to straight stitch.
Set the stitch length dial to between 2 and 3.
•
Using the fingerhold on the left-hand side, pull firmly
upwards and forwards to remove the extension table.
•
Inside the extension table is the storage compartment.
Open the storage compartment with a sharp tug, to
find various accessories and a number of bobbins.
Related Manuals for Brother XL5060NTC
-
Bernina Sewing Machine 801 Owner's Manual
23 pages
-
Bernina Sewing Machine Bernette 320 / 330 Owner's Manual
29 pages
-
Bernina Sewing Machine Bernette 410 / 420 / 430 / 440 Owner's Manual
31 pages
-
Bernina Sewing Machine 800DL Owner's Manual
40 pages
-
Bernina Sewing Machine Record 930 Electronic User's Manual
52 pages
-
Brother Sewing Machine Sewing Machines Operation Manual
140 pages
-
Euro-Pro Sewing Machine 8260 Instruction Manual
75 pages
-
Euro-Pro Sewing Machine 1100H Dressmaker Instruction Manual
6 pages
-
Kompernass Sewing Machine LERVIA KH 4000 Operation Manual
34 pages
-
Shark Sewing Machine Euro-Pro 384 Instruction Manual
53 pages
-
Simplicity Sewing Machine Serge Pro SW432 Instruction Manual
27 pages
-
Singer Sewing Machine 8280 Instruction Manual
50 pages
-
Singer Sewing Machine 3116 Simple Instruction Manual
94 pages
-
Singer Sewing Machine ATHENA 2000 Instruction Manual
25 pages
-
Singer Sewing Machine Touch Tronic 2010 Owner's Manual
27 pages
-
JANOME Sewing Machine MS-5027 User's Manual
111 pages
-
Singer Sewing Machine 306K User's Manual
50 pages
-
Singer Sewing Machine 50T8 E99670 User's Manual
94 pages
-
Singer Sewing Machine Prelude 8280 User's Manual
50 pages
-
Brother Sewing Machine XL3022 User's Manual
59 pages
-
Pfaff Sewing Machine 463 AND 463 H User's Manual
14 pages
-
Bernina Sewing Machine 950 Industrial User's Manual
3 pages
-
Bernina Sewing Machine service manual 730 User's Manual
51 pages
-
Bernina Sewing Machine 1130 Instruction Manual
59 pages