Brother PC-3000 Owner's Manual
A
Filling the bobbin
Place the thread spool on the spool pin and pass the
thread around the bobbin winder thread guide.
Pass the thread through
the hole on the bobbin
from inside, and slide the
winding shaft to the right.
While holding the end of
the thread, depress the
foot controller.
When the bobbin is full, it
will stop winding.
Cut the thread, slide the
winding shaft to the left
and remove the bobbin.
Hold the bobbin case as
shown, insert the bobbin
with the thread coming
from the bottom toward the
top and the thread tail
hanging out of the bobbin
case.
Pull the thread tail into the bobbin
case groove, under the spring clip
and into the thread guide hole.
Holding the bobbin case by
the latch align the finger
with the top opening of the
shuttle race , insert the
case into the shuttle race
and release the latch. The
latch should hold the
bobbin case in place.
Raise the needle to its
highest position and
remove the bobbin case by
pulling the latch.
B
Threading the needle
Raise the presser foot lifter.
Raise the thread take-
up lever to its highest
position by turning the
balance hand wheel.
Pass the thread through the thread guide and down the right
channel on the front of the machine.
Place the thread
spool on the spool
pin.
Pass the thread into the thread tension discs or *behind the
thread tension dial from the right to the left.
Grasp the thread on both
sides of the tension disc
and pull to ensure it is in
place.
Guide the thread up the left channel, clear to the back of the opening
around the take-up lever and back down the left side of the channel to
thread the take-up lever.
Thread the needle from
front to back and pull out
about 2” of thread.
C
Thread tension
Upper thread tension is too tight.
(Locks appear on the surface of the fabric.)
Decrease the tension by turning the dial to a lower number.
Upper tension is too loose.
(Locks appear on the reverse side of the fabric.)
Increase the tension by turning the dial a higher number.
∗If these actions do not correct the problem, please rethread the machine using step A and B.
Correct thread tension
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
*
Related Manuals for Brother PC-3000
-
Brother Printers VX-1120 Owner's Manual
104 pages
-
Brother Printers PT-1000 Owner's Manual
163 pages
-
Ricoh Printers Aficio MP 4002 Owner's Manual
228 pages
-
Ricoh Printers Aficio SP 3510SF Owner's Manual
476 pages
-
Ricoh Printers Aficio SP C242SF Owner's Manual
456 pages
-
Ricoh Printers MP C4503 Owner's Manual
240 pages
-
Uniden Printers HOMEPATROL-1 Owner's Manual
39 pages
-
Uniden Printers BCT15X Owner's Manual
1 pages
-
Canon Printers PIXMA MP495 Owner's Manual
68 pages
-
Canon Printers PIXMA MG5220 User's Manual
20 pages
-
Canon Printers PIXMA MG3520 User's Manual
34 pages
-
Canon Printers PIXMA MG2520 User's Manual
34 pages
-
Epson Printers XP-100 Range manual
7 pages
-
Epson Printers LX-310 Specifications
2 pages
-
HP Printers Officejet 6700 User's Manual
226 pages
-
HP Printers LaserJet Pro 400 Service Manual
346 pages
-
HP Printers Officejet Pro 8610 User's Manual
268 pages
-
HP Printers Officejet 4630 e User's Manual
166 pages
-
HP Printers ENVY 4500 User's Manual
108 pages
-
HP Printers Deskjet 2540 User's Manual
102 pages
-
HP Printers ENVY 5530 User's Manual
108 pages
-
HP Printers OFFICEJET 4500 User's Manual
228 pages
-
Epson Printers 220 User's Manual
28 pages
-
Xerox Printers Phaser 3260 User's Manual
174 pages