Brother BAS-611 Owner's Manual | Page 66
60
LK3-B434E Mark II
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from
the wall outlet before opening the face plate of the control box. Touching areas where high volt-
ages are present can result in severe injury.
15. TABLE OF ERROR CODES
DANGER
If a malfunction should occur with the sewing machine, a buzzer will sound and an error code will appear in
the display window. Follow the remedy procedure to eliminate the cause of the problem.
15. TABLE OF ERROR CODES
Turn off the power and check.
Emergency stop switch is being
continually pressed, or emergency switch
connection error.
E-12
Machine motor operation error.
E-13
E-20
E-21
E-30
E-32
E-31
E-40
E-41
E-42
E-50
E-60
E-61
E-62
E-63
E-70
Machine specification select connector is
not connected properly.
Problem with machine motor stopping, or
synchronizer connection error.
Data is outside possible sewing area due
to enlargement ratio setting.
The data format of the user program (% or
mm) does not match the setting of DIP
switch A-6.
After changing the setting of DIP switch A-6, clear
all memory settings. (Refer to “10-14. Clearing all
memory settings”.)
Stitch pattern data overlaps the sewing
area when area limiting is active.
Length of a stitch exceeds 10 mm.
Abnormality in the sewing data.
Invalid program number specified.
Needle bar does not stop when the needle
is raised.
Presser has not been lowered.
Presser cannot be raised.
Presser is not raised.
Presser cannot be lowered.
Cooling fan does not operate.
Turn off the power and check if connectors P3 is
disconnected.
Turn off the power, and then turn the machine
pulley to check if the machine has locked up. Check
the synchronizer connection. Check if connectors
P11, P12 and P13 are disconnected.
Turn off the power and check the ground wire
connection.
Press the RESET switch, and then set the
enlargement ratio again.
Press the RESET switch, and then reset the memory
switches “30” and “31” or enlargement ratio.
Press the RESET switch, and then set the
enlargement ratio again.
If programming a new sewing data, repeat the
procedure from the beginning.
Press the RESET switch and specify a correct
number.
Turn the pulley to align the index mark with the
needle up stop position. (Refer to “10-10. Adjusting
the needle up stop position”.) Check the V-belt
tension. (Refer to “3-15. Installing the V-belt”.)
Refer to “17. Troubleshooting”.
Turn off the power and check the connection of
presser sensor connector P1.
Turn off the power, and then check if the cooling
fan is blocked with scraps of thread.
E-10
E-11
Cause
Emergency stop switch was pressed.
Emergency stop switch was pressed
during sewing.
Remedy
Turn the EMERGENCY STOP switch clockwise to
release the lock, and then press the RESET switch
to reset the error.
Turn the EMERGENCY STOP switch clockwise to
release the lock, and then press the RESET switch
to reset the error. You can then press the BOBBIN.
WIND switch to repeat the sewing.
Code
Related Manuals for Brother BAS-611
-
Logitech Misc Electronics O-R0004 Quick Start Manual
2 pages
-
Brother Misc Electronics DB2-B755 MKIII Owner's Manual
4 pages
-
Panasonic Misc Electronics KX-TG6572R Owner's Manual
64 pages
-
Technics Misc Electronics SA-AX720 Owner's Manual
36 pages
-
RCA Misc Electronics RCR504BR Owner's Manual
2 pages
-
RCA Misc Electronics RCRN04GR Owner's Manual
2 pages
-
Intermatic Misc Electronics GM40AVE Owner's Manual
12 pages
-
Intermatic Misc Electronics ET70115 and ET70215 Owner's Manual
20 pages
-
Intermatic Misc Electronics ET1705C Owner's Manual
4 pages
-
Kidde Misc Electronics Firex 2650-560,2650-561 English MA2650 Owner's Manual
6 pages
-
Trane Misc Electronics XL800 Owner's Manual
8 pages
-
Trane Misc Electronics XL803 Owner's Manual
8 pages
-
Trane Misc Electronics XL624 Owner's Manual
8 pages
-
Trane Misc Electronics XL600 Owner's Manual
8 pages
-
Trane Misc Electronics XL80 Owner's Manual
12 pages
-
Trane Misc Electronics XR80 Owner's Manual
12 pages
-
Trane Misc Electronics XB80 Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics CS 4325 Chipper Shredder Owner's Manual
36 pages
-
Troy-Bilt Misc Electronics TB146 EC 4-Cycle Garden Cultivator Owner's Manual
16 pages
-
Troy-Bilt Misc Electronics TB516 EC Lawn Edger Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics Colt FT Garden Tiller Owner's Manual
36 pages
-
Linear Misc Electronics AP-4 Owner's Manual
2 pages
-
Brother Misc Electronics KE-430F Parts Manual
68 pages
-
Hunter Misc Electronics XC Programming Instructions Manual
18 pages