BRITAX Verve User's Manual

BRITAX High Chair User's Manual - Verve.
Download
Page  of 2
4.1, 1558 votes
background image

User Guide

UK

2 Attaching your child seat for use as a travel system 

(this vehicle is intended for children from birth and up to 13kgs) 

Verve P-Type 

adaptor

Verve P-Type 

socket

To remove the child 

seat move the handle 

to the carrying position. 

Lift the lever on the 

adaptors and lift the 

child seat out of the 

sockets 

(dia 2d)

IMPORTANT - 

It may be necessary to 

remove the adaptors 

from the child seat 

when instal ing it in 

your vehicle.

If the adaptors are in 

contact with the vehicle 

seat cushion, remove 

them. 

To remove the 

adaptors from the child 

seat, pul  the lever on 

the adaptors away from 

the child seat while 

pul ing down 

(dia 2e)

Repeat the process for 

both adaptors.

The child seat is 

compatible with 

the ISOFIX base 

(purchased separately). 

See 

www.britax.eu for 

further information.

Only use a P-Type child seat on this buggy when fitted with a Verve P-Type socket

HANDY HINT - 

You may find it easier 

to apply the brake 

when fitting the child 

seat. Please refer to 

the user guide for your 

buggy.

Clip the socket onto 

the chassis from the 

inside. Align the bottom 

edge of the socket with 

the edge shown on 

the chassis 

(dia 2a)

Rotate the fixing arm. 

Squeeze the housing 

and fixing arm together 

with one hand and 

snap over the hook 

with the other hand.

Repeat this process for 

both sockets.

Ensure that the left 

hand and right hand 

sockets are used on 

the correct side of the 

buggy.

To fit the adaptor to the 

child seat squeeze the 

lever and insert into 

the space below the 

handle 

(dia 2b). Make 

sure it is ful y fitted and 

release the lever to 

lock into place. Repeat 

this process for both 

adaptors.

Ensure that the left 

hand and right hand 

adaptors are used on 

the correct side of the 

child seat.

IMPORTANT - 

The buggy seat unit 

must be removed 

before attaching your 

car seat.

Lower the child seat 

onto the buggy making 

sure that the adaptor 

on either side drops 

into both the sockets on 

each side of the buggy 

(dia 2c). Push down 

firmly. Once the seat is 

engaged you wil  hear 

a click. 

Move the handle to 

the rocking position. 

Please refer to the user 

guide for the child seat.

WARNING - 

Check that the child 

seat attachment 

devices are correctly 

engaged before use.

IMPORTANT - 

Ensure your child is 

harnessed at al  times.

Unclip the hooks on 

both sides of the buggy 

(dia 1d).

Remove the seat unit 

from the chassis by 

sliding the base tabs 

upwards and out of the 

grooves.

Then slide the top tabs  

upwards and out of the 

grooves until the seat 

unit is disengaged  

(dia 1e).

To re-fit the seat 

unit reverse these 

instructions.

HANDY HINT - 

You may find it easier 

to apply the brake 

before removing or 

re-fitting the seat unit.

Please refer to the user 

guide for your buggy for 

operation of the brake.

Unfasten the press 

studs    on the backrest 

and unfasten the hook 

and loop fastenings on 

both sides of the seat 

unit where it overlaps 

the hood     

(dia 1a).

HANDY HINT - 

You may find it easier 

to stand behind or to 

the side of the buggy. 

Remove the hood 

and bumper bar 

by simultaneously 

pressing the buttons on 

the mouldings on both 

sides of the buggy and 

slide them upwards 

until they disengage 

(dia 1b).

Unfasten the hook and 

loop fastenings and 

press studs shown by 

the red circles  

(dia 1c).

1 Removing or re-fitting your seat unit  

(the seat cover must be removed before fitting the infant carrier) 

B

A

BBO-662-00

A

B

1a

1b

1c

1d

B

B

A

A

1e

2b

2c

2d

2e

2a

1282.000 - Verve Adaptors & Sock1   1

10/1/07   09:15:40

Also See for BRITAX Verve

0.648824s