Black & Decker Black & Decker Angle Grinder 7750 User's Manual

Black & Decker Grinders User's Manual - Black & Decker Angle Grinder 7750.
Download
Page  of 5
4.9, 1235 votes
background image

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY
• Double insulated tools are equipped with a polarized plug (one blade is wider than

the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug in any way
. Double insulation 
eliminates the need for the three wire grounded power cord and grounded power supply
system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. 
Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A"

or "W". These cords are rated for outdoor use and reduce the risk of electric shock. 

PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. 
A moment of inattention while operating power tools may result in serious
personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair
can be caught in moving parts. Air vents may cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is

left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventative safety measures reduce
the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced
before using. 
Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on
another tool.

SERVICE
• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES
• Always use proper guard with grinding wheel. A guard protects operator from broken

wheel fragments. Always position the guard so that as much of the exposed disc as possible
is pointing away from you.

• Accessories must be rated for at least the speed recommended on the tool warning

label.

Wheels and other accessories running over rated speed can fly apart and cause

injury.  

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord.

Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

ADDITIONAL SAFETY RULES
• ALWAYS WEAR EYE PROTECTION.
• Wear ear protection. noise level may be amplified when grinding in enclosed spaces.
• KEEP GUARDS IN PLACE WHEN GRINDING.
•  Use only accessories having a maximum operating speed at least as high as the speed

specified in the warning on the tool’s label. NEVER use Type11 (Flaring Cup) wheels on this
tool.

•  Before using, inspect recommended accessory for cracks or flaws. If such a crack or flaw is

evident, discard the accessory. The accessory should also be inspected whenever you think
the tool may have been dropped.

• When starting the tool (with a new or replacement wheel or brush installed) hold the tool in a

well protected area and let it run for one minute. If the wheel or brush has an undetected
crack or flaw, it should burst or separate in less than one minute. Never start the tool with a
person in line with the accessory. This includes the operator.

•  In operation, avoid bouncing the wheel or giving it rough treatment. If this occurs, stop the

tool and inspect the wheel.

• ALWAYS USE GUARDS with grinding wheels and wire cup brushes. Sanding discs and flat

wire brushes may be used without guards. Always position the guard so that as much of the
exposed wheel or wire brush as possible is pointing away from you.

• Always wear eye, face and body protection when brushing.  Brush filiments may break

and be thrown at operator.

• Clean your tool out periodically.
•  Do not use Type 1 cutting or diamond wheels. Proper guards are not available. Use

conventional Type 27 depressed center (non-hubbed) wheels only.

CAUTION: Use extra care when grinding into a corner as a sudden, sharp, movement of

the grinder may be experienced when the wheel contacts a secondary surface.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other repro-
ductive harm. Some examples of these chemicals are:

•  lead from lead-based paints,
•  crystalline silica from bricks and cement and other masonry products, and 
•  arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals:  work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. 
Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals. 

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.
The label on your tool may include the following symbols.

V ..........................volts

A..........................amperes

Hz ........................hertz

W ........................watts

min ........................minutes

......................alternating current

......................direct current

no ........................no load speed

..........................Class II Construction

........................earthing terminal

........................safety alert symbol

.../min ..................revolutions or 

reciprocations
per minute

CAT. NO. 7750      

FORM NO. 581596-00    

PRINTED IN CHINA

(MAR - 02 )

KEY INFORMATION YOU SHOULD

KNOW:

• Wait until tool reaches full speed before

applying to work. Remove from work and
allow to stop before setting down.

•  Hold grinder at proper angle, as shown in

figures 11 and 12.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 

INSTRUCTION MANUAL

Catalog Number 7750

4-1/2  inch  Angle  Grinder

1-800-54-HOW-TO

BEFORE RETURNING THIS PRODUCT 

FOR ANY REASON PLEASE CALL

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PURCHASE,

CALL 1-800-54-HOW-TO (1-800-544-6986).

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE.

IF YOU HAVE A SUGGESTION OR COMMENT,

GIVE US A CALL. YOUR FEEDBACK IS VITAL

TO THE SUCCESS OF BLACK & DECKER’S QUALITY 

IMPROVEMENT PROGRAM.

(544-6986)

1.)  ON/OFF SWITCH / INTERRUPTEUR COULISSANT

/ INTERRUPTOR DESLIZABLE

2.)  LOCK-ON BUTTON / BOUTON DE

VERROUILLAGE / BOTON DE ENCENDIDO

PERMANENTE

3.)  SPINDLE LOCK BUTTON / BOUTON DE

VERROUILLAGE D'ARBRE / BOTON DE SEGURO DE

LA FLECHA

4.)  ACCESSORY WHEEL / MEULE ACCESSOIRE /

DISCO ACCESORIO

5.)  AUXILIARY HANDLE / POIGNÉE AUXILIAIRE /

MANGO AUXILIAR

6.)  WHEEL GUARD / CARTER DE MEULE / GUARDA

DEL DISCO

1

4

5

6

1

3

4

5

6

2

2

6

11

4

9

6

8

10

3

9

12

4

12

14

6

4

8

7

0.677198s