Behringer V-AMP 2 User's Manual | Page 9

Behringer Musical Instrument Amplifier User's Manual - V-AMP 2.
Download
Page  of 19
4.4, 2495 votes
background image

9

            V-AMPIRE/V-AMP PRO/V-AMP 2

3.3.1 V-AMPIRE

Not  only  does  the  V-AMPIRE  has  its  own  built-in  speaker,

which means you can plug in and play without further equipment,

the  V-AMPIRE  also  allows  to  connect  a  second  external

loudspeaker.  Using  the  left  speaker  output  mutes  the  internal

speaker, diverting the full 100 W to the external 4 Ω speaker (see

fig.  1.4).  This  makes  sense  particularly  if  the  external  speaker

has  a  specific  sound  which  cannot  be  recreated  using  the

internal speaker.

You  can  also  connect  to  an  external  stereo  speaker

arrangement, e.g. our BG412S. In this configuration the V-AMPIRE

developes  2  x  50  W  into  8  Ω  per  side.  This  lets  you  take  full

advantage of the V-AMPIRE’s stereo effects (fig. 1.5).

Alternatively,  an  external 8  Ω speaker  may  be  connected  to

the  right  speaker  output.  This  also  represents  a  stereo

configuration,  because  the  internal  speaker  is  not  muted,  as

shown in fig. 1.6.

The starting configuration for this application would be L2, i.e.,

a stereo signal with all effects, amp simulation and live EQ but no

speaker simulation. The ULTRA-G speaker simulation is available

at the XLR output and thus connectable to a sound reinforcement

system.  Here,  the  MASTER  control  only  influences  the  stage

volume but not the XLR output. If you want to listen to a digital

speaker simulation using an amplifier, select L1.

3.3.2 V-AMP PRO

Because  of  its  additional  outputs  and  the  analog  ULTRA-G

speaker  simulation  the  V-AMP  PRO  is  even  more  flexible  on

stage. Figure 2.5 shows a stereo application with active stage

monitors which are connected to the unbalanced line outs. Use

the MASTER control to set the volume of the monitor speakers

while  the  XLR  output  signal  is  sent  at  full  volume  to  a  sound

reinforcement  system.  The  appropriate  modes  are  S1  or  L1

depending on whether the 3-band EQ is needed or not.

Since the receiver of the wireless system is connected to the

rear line input, the line input switch on the front has to be pressed.

Use this switch also to mute the signal while you change your

guitar.

Figure 2.6 displays a very similar application: The monitor amp

in this case is a guitar amp so that mode L2 (no speaker simulation)

is recommendable.

3.3.3 V-AMP 2

Figure 3.5 on the view sheet shows the V-AMP 2 connected

from its line out to the line input of the guitar amp or head. Using

the instrument input would not be the best idea since the signal

is passed through the whole pre amplifier stage. BEHRINGER

offers a wide range of guitar amps which are equipped with an

aux input and thus are perfect for this application. Since a guitar

amp already has its own sound, a digital speaker simulation is

not needed. We therefore recommend mode L2.

Figure  3.6  describes  another  speciality  of  the  V-AMP  2  in

mode  L3:  A  guitar  amp  is  used  as  monitor  speaker  on  stage

while  simultaneously  a  second  signal  is  sent  to  a  sound

reinforcement system. By doing so, you can completely eliminate

the need for miking the amp.

A special feature of the L3 mode is that the signal to the guitar

amp  has  no  speaker  simulation,  instead  it  has  an  additional

3-band EQ which allows you to tailor your on-stage sound. The

signal  for  the  sound  reinforcement  system  remains  unaffected

by the 3-band EQ, but it does include the speaker simulation. This

simulation  is  necessary  to  reproduce  the  character  of  a  guitar

cabinet  sound  using  the  speakers  of  the  sound  reinforcement

system.

3.4 Recording

For this applications we assume that at least a mixing console

and a recording device is available.

3. OPERATING MODES AND APPLICATIONS

3.4.1 V-AMPIRE

As with rehearsals at home or anywhere else, the V-AMPIRE

can be connected directly to a mixing console or recording device

via its XLR outputs. In addition, you can use the pre DSP insert

send  to  record  the  same  direct  guitar  signal  without  needing

another DI-box for impedance adaption.

Since  the  usual  volume  problem  does  not  exist  in  studio

environments, the V-AMPIRE has more to offer than those features

described in chapter 3.2.1. In the studio you can raise the volume

to take full advantage of the V-AMPIRE’s own sound. If you have

a particular speaker cabinet with its own sonic character you can

drive it via the speaker output. You will need to use a microphone

to  capture  this  special  sound.  If  you  want  to  create  intentional

feebacks from the speaker, you can still feed the XLR output into

the console to be recorded. We recommend mode L2, with 3-band

EQ but without digital speaker simulation (see fig. 1.4).

 3.4.2 V-AMP PRO

For studio applications we recommend modes S1, S2 or S3.

S1 reproduces all amp and speaker simulations with effects in

stereo  (as  with  the  V-AMP  2)  while  with  S2,  the  effects  are

applied to the right channel only. In mode S3, the digital speaker

simulation is shut off for the case that the speaker sound is to be

determined  later  during  mixdown.  Therefore,  in  S3  mode  the

proven ULTRA-G speaker simulation is switched to the XLR and

headphones outputs. When recording in S3 mode, the monitoring

should thus be done at the analog XLR and headphones outputs

and not at the digital outs. If you want to record the original guitar

signal you could use the setup shown in fig. 2.3. Press the LINE

INPUT switch if you want to monitor the recorded signal via the

V-AMP PRO.  We recommend to use modes S1 or L1. Mode S2 is

an alternative if you want to adjust the effect ratio on the mixing

console.
+ Please note that the ULTRA-G speaker simulation

in  modes  S3  and  L2  only  affects  the  XLR  and

headphones  outputs  and  does  not  have  any

influence  on  the  digital  outputs.

3.4.3 V-AMP 2

To  record  a  stereo  signal  with  all  effects,  amp  and  speaker

simulations, select modes S1 or L1 (with 3-band EQ) and connect

the balanced line outs with the mixing console or recording device.

This advantage is a disadvantage at the same time:

You hear the sound exactly the way you record it. So if you

decide  to  make  a  change,  you  will  need  to  record  the  whole

track again.

With studio mode S2 all effects are therefore put out through

the right channel only, while on the left channel you will find the

amp and speaker simulations. This enables you to record the dry

amp signal and determine the effects later on during mixdown

(see  fig.  3.4).

If you want to go the safe way, we recommend to split up the

input signal with a high-quality active DI-box, e.g. the BEHRINGER

GI100. To do this, connect the guitar to the GI100 input, the direct

link  to  the  input  of  your  V-AMP  2  and  the  XLR  output  to  the

recording device. In that manner, you can record the direct guitar

signal with the amp simulation on one channel each and listen to

the  complete  signal  with  all  effects  on  your  headphones  (see

fig.  3.4).

Related Manuals for Behringer V-AMP 2

0.593922s