Behringer Behringer DJ Equipment NOX606 User's Manual | Page 10
18
PRO MIXER NOX202/NOX303/NOX404/NOX606/NOX1010
19
Quick Start Guide
NOX202/NOX303/NOX404/NOX606/NOX1010 Contr ols
(EN)
Step 2: Controls
Mic Channels
AUX 1/2 knobs adjust the channel’s signal at the
(1)
AUX SEND 1 and 2 jacks. The PRE buttons al ow the
channel’s signal to be sent to the AUX SEND jack
pre-fader.
MIC/RTN switch selects either the XLR MIC input or the
(2)
stereo ¼" RETURN jacks as the channel’s audio source.
MIC EQ knobs adjust the channel’s equalization. On the
(3)
NOX606, the MID 1 knob adjusts the high midrange
frequencies and MID 2 adjusts the lower mids.
MIC GAIN knob controls the sensitivity of the mic input.
(4)
On the NOX1010, the knob acts as a volume control.
TALKOVER causes the music volume to automatical y drop
(5)
whenever the mic is in use, al owing the operator to be
heard over the music. On the NOX606, hold the switch in
the up position to engage the talkover function, and flip
the switch down to turn the mic channel on without
attenuating the music.
ON/PEAK LED lights green to indicate that the channel
(6)
has been activated, and lights red if the audio begins
to overload.
MIC ON button engages the mic channel.
(7)
AUX IN knob adjusts the level of the audio connected to
(8)
the AUX IN jacks.
Stereo Channels
GAIN knob controls the sensitivity of the channel input.
(9)
INPUT SELECT switch selects the channel’s audio source.
(10)
CUE button al ows the source to be monitored without
(11)
being included in the master output section.
CHANNEL EQ knobs boost or cut the high, mid and low
(12)
frequencies of the channel. On the NOX404, use the
EQ ON/OFF switch to engage the knobs.
FILTER switch sends the channel to either FILTER 1 or 2.
(13)
Leave the switch in the center to bypass the filters.
XFADE (A OFF B) switch sends the channel to either side of
(14)
the crossfader. When the center OFF position is selected,
a channel whose fader is raised will bypass the crossfader
and be heard in the main mix.
CHANNEL FADER controls the volume of the channel in
(15)
the overall mix.
CHANNEL VU METER displays the signal level of the
(16)
input source.
PAN fader adjusts the channel’s left to right balance.
(17)
Crossfader Section
FADER START switch engages the fader start function,
(18)
al owing the mixer to send start/cue signals to an
auto-start CD player.
CF ASSIGN knobs determine which channels appear at
(19)
either side of the crossfader.
CROSSFADER fades between the sources assigned to
(20)
either side.
XFADE CURVE knob determines how steep or gradual the
(21)
fade between source A and source B is.
REV/MODE LEDs indicate the status of the REVERSE and
(22)
MODE 1/2 buttons.
KILL switches/buttons remove the high, mid and low
(23)
frequencies from the A or B crossfader mix. On the
NOX303, flip the switches up to lock the effect,
or manual y hold the switches down to briefly remove
the selected frequencies.
FX Section
FX DISPLAY indicates the current effect. The display will
(24)
flash when a new effect is selected, and remain lit when
it is confirmed by pressing the FX SELECT button.
FX SELECT knob scrol s through the available effects.
(25)
Pressing the knob confirms the effect selection.
FX ON button activates the digital effects processor.
(26)
FX CUE button sends the effect to the cue section for
(27)
preview before applying it to the mix.
FREQUENCY knob adjusts a frequency-based or
(28)
time-based parameter of the selected effect.
INTENSITY fader adjusts the mix or resonance parameter
(29)
of the selected effect.
FX ASSIGN knob determines which sources are affected
(30)
by the effect.
TAP button al ows the effect’s tempo parameter to be
(31)
manual y entered by pressing in rhythm with the music.
Holding the TAP button for 2 seconds will cause the
button to light permanently and al ow the FREQUENCY
knob to continuously control the effect's tempo.
DATA/MIDI knob al ows adjustment of data such as MIDI
(32)
clock speed.
MIDI ON button sends MIDI start/stop data to an
(33)
external sequencer.
Master Section
BALANCE knob adjusts the left to right balance of the RCA
(34)
MAIN OUTPUTS and BALANCED OUTPUTS.
BOOTH knob controls the level of the RCA BOOTH
(35)
OUTPUTS on the back panel.
MONO button switches the BOOTH signal from stereo
(36)
to mono.
MUTE button mutes the BOOTH output.
(37)
MASTER fader/knob controls the level of the RCA MAIN
(38)
OUTPUTS and BALANCED OUTPUTS.
AUX OUT knob adjusts the output of the AUX OUT jacks,
(39)
which carry the same signal as the MAIN OUTPUTS.
MIX 1 knob adjusts the output of the MIX 1 XLR outputs
(40)
on the rear panel.
MIX 2 knob adjusts the output of the MIX 2 ¼" jacks on
(41)
the rear panel.
MASTER VU METER displays the signal level of the master
(42)
output and/or cue signal.
MASTER/CUE button determines whether the MASTER
(43)
VU METER displays the signal from the master output or
cue signal.
CUE ACTIVE LED lights when a channel’s CUE button
(44)
is active.
POST EQ button selects whether the cue is taken pre (up)
(45)
or post-EQ (down).
STEREO/MONO button al ows the master output signal to
(46)
send in stereo or mono mode.
SPLIT/BLEND(CUE) button al ows the cue signal to
(47)
combine the cue and program sources or separate the
sources into left (cue) and right (main).
AUX 1/2 switches send the selected AUX RETURN signal
(48)
to the cue mix.
CUE GAIN knob determines the volume and sensitivity of
(49)
the cue signal.
CUE MIX knob/fader al ows a gradual blend between the
(50)
cue signal and the program signal. On the NOX404 and
NOX202, this fades between channel 1 and 2.
CUE MODE switch determines whether channels 1 and 2,
(51)
the FX section, or the Master signal are heard in the cue/
headphone mix.
Rear Panel
POWER SWITCH turns the power to the unit on and off.
(52)
LINE/PHONO button optimizes the PHONO jacks for use
(53)
with a turntable or CD player.
Front Panel
CUE TONE knob adjusts the tone of the
(54)
cue/headphone signal.
REV/CF REVERSE button switches the assignment of the
(55)
signals present at either side of the crossfader.
MODE button determines whether XFADE CURVE A or B
(56)
is active.
FX LOOP/CONTOUR section (NOX404)
FX LOOP CH1/2 switches send the channel to the FX LOOP
(57)
SEND jack.
FX LOOP MIX fader adjusts how much of the FX LOOP
(58)
RETURN signal is included in the main mix.
CH REV button al ows the channels faders to control
(59)
either input 1 or input 2.
MONO 1/2 STEREO HOUSE switch enables the VU METERS
(60)
to either display channels 1 and 2 separately or the
overall stereo mix.
REVERSE button changes the function of the CHANNEL
(61)
FADER so that the top position is off and the bottom
position is full volume.
MODE 1/2 button selects whether the CHANNEL FADER
(62)
acts as a volume control (MODE 1) or as a pan control
(MODE 2).
CONTOUR fader either adjusts the CHANNEL FADER
(63)
volume slope or the pan slope, depending on
MODE 1/2 selection.
Filter Section (NOX606)
LFO DEPTH knob adjusts the amount of LFO
(64)
(low-frequency oscil ator) modulation applied to
the filter.
LFO ON button engages the LFO.
(65)
X2 TEMPO button doubles the speed of the LFO.
(66)
TAP button al ows the speed of the LFO to be manual y
(67)
entered by tapping in rhythm with the music.
RESONANCE knob determines the sharpness of the
(68)
filter, al owing a smooth response at the ‘MILD’ end to a
resonant feedback boost when turned towards ‘WILD’.
VCF LINK 2-1 al ows FILTER 2 to be control ed by FILTER
(69)
1, al owing both filters to be adjusted simultaneously.
The HPF, BPF and LPF buttons still function
independently for each filter.
VCF TO XFADER button al ows the filter's FREQUENCY
(70)
function to be control ed by the crossfader.
HPF button engages the high-pass filter, al owing only
(71)
the frequencies above the FREQUENCY knob setting to
be heard.
BPF button engages the band-pass filter, al owing only
(72)
the narrow band of frequencies selected by the
FREQUENCY knob to be heard.
LPF button engages the low-pass filter, al owing only
(73)
the frequencies below the FREQUENCY knob setting to
be heard.
FREQUENCY knob selects the frequency used by the
(74)
variable cutoff filter.
FILTER ON button engages the filter.
(75)
Normal Slow Fade
Fast Cut
Reverse Normal Slow Fade
Reverse Fast Cut
Soft Pan
Fast Pan
Related Manuals for Behringer Behringer DJ Equipment NOX606
-
Behringer DJ Equipment X32 DIGITAL MIXER User's Manual
70 pages
-
Yamaha DJ Equipment FX500 Operation Manual
97 pages
-
Yamaha DJ Equipment GF16/12 Owner's Manual
26 pages
-
Yamaha DJ Equipment GF24/12 Owner's Manual
26 pages
-
Yamaha DJ Equipment SPX50D Operation Manual
105 pages
-
Denon DJ Equipment Denon DJ Equipment DN-X1600 User's Manual
32 pages
-
Denon DJ Equipment Denon DJ Equipment DN-X500 User's Manual
63 pages
-
Kenwood DJ Equipment TK-260G User's Manual
50 pages
-
Kenwood DJ Equipment TK-270G User's Manual
50 pages
-
Peavey DJ Equipment DeltaFex Twin User's Manual
23 pages
-
Behringer DJ Equipment PRO MIXER VMX300 VMX300 User's Manual
13 pages
-
Dynacord DJ Equipment PowerMate 600 User's Manual
64 pages
-
ION DJ Equipment DISCOVER DJ User's Manual
16 pages
-
Lexicon DJ Equipment MPX 550 User's Manual
111 pages
-
Roland DJ Equipment SP-404SX User's Manual
54 pages
-
Samson DJ Equipment XP510I User's Manual
2 pages
-
Allen & Heath DJ Equipment ZED 12 FX User's Manual
36 pages
-
Allen & Heath DJ Equipment ZED 22 FX User's Manual
36 pages
-
Allen & Heath DJ Equipment ZED-10FX User's Manual
32 pages
-
American Audio DJ Equipment q-d6 User's Manual
17 pages
-
American DJ DJ Equipment FS-1000 User's Manual
2 pages
-
Denon DJ DJ Equipment Denon DJ DJ Equipment DN-MC6000 User's Manual
2 pages
-
Stanton DJ Equipment SCS.4DJ User's Manual
64 pages
-
Behringer DJ Equipment X32 DIGITAL MIXER User Manual
70 pages