Avaya BSG12 User's Manual

Avaya Business Services Gateway User's Manual - BSG12.
Download
Page  of 2
4.9, 1304 votes
background image

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.
WARNING: To comply with FCC radio frequency (RF) exposture limits, install this device a minimum of 7.9 inches 

(20 cm) away from individuals.

The following safety instructions cover the installation and use of the Product. Read carefully and retain for future 

reference. 
Installation 
WARNING:
 To avoid electrical shock hazard to personnel or equipment damage observe the following precautions 

when installing telephone equipment: 
1. Never install telephone, LAN or WAN wiring during a lightning storm. 
2. Never install telephone, LAN or WAN jacks in wet locations unless the jack is specifically designed for wet locations. 
3. Never touch uninsulated telephone, LAN or WAN wires or terminals unless the line has been disconnected at the 

network interface. 

4. Use caution when installing or modifying telephone, LAN or WAN lines. The exclamation point within an 

equilateral triangle is intended to alert the user to the presence of important operating and maintenance 
(servicing) instructions in the literature accompanying the product. 

5. This product should be installed by a qualified/trained installer.
6. Disconnect the telecommunications network connector before you disconnect the power to this 

product.

Use 
When using your equipment, basic safety precautions should always be followed to reduce risk of fire, electric shock and 

injury to persons, including the following: 
1. Read and understand all instructions.
2. Follow the instructions marked on the product and in the User and Maintenance documentation.
3. Unplug this product (or host equipment) from the wall outlet before cleaning. Do not use liquid cleaners or aerosol 

cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet 

basement, or near a swimming pool. 

5. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to 

the product.

6. This product should never be placed near or over a radiator or heat register. This product should not be placed in a 

built-in installation unless proper ventilation is provided.

7. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons 

walking on it.

8. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
9. Never spill liquid of any kind on the product.
10. To reduce the risk of electric shock do not disassemble this product, but have it sent to a qualified service person 

when some service or repair work is required. 

11. Unplug this product (or host equipment) from the wall outlet and refer servicing to qualified service personnel under 

the following conditions: 
a) When the power supply cord or plug is damaged or frayed.
b) If the product has been exposed to rain, water or liquid has been spilled on the product, disconnect
and allow the product to dry out to see if it still operates; but do not open up the product.
c) If the product housing has been damaged.
d) If the product exhibits a distinct change in performance.

12. CAUTION: 

To eliminate the possibility of accidental damage to cords, plugs, jacks, etc., do not use sharp 

instruments during the assembly procedures

13. WARNING: Ensure the correct connections are being made to the equipment. Incorrect connections may result in a 

shock or fire hazard.

14. Save these instructions.

North American Regulations continued

Important Safety Instructions

RTTE01

Regulatory and Safety Information for BSG12

 

This Class A device complies with Part 68 and Part 15 of the FCC Rules and the requirements adopted by the ACTA. 

This device meets the applicable Industry Canada specifications including ICES-003 EMI requirements. Operation is 

subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must 

accept any interference received, including interference that may cause undesired operation.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or 

alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications 

company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the 

electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, 

are connected together. This precaution may be particularly important in rural areas. 

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric 

inspection authority, or electrician, as appropriate. 
Do not attempt to repair this equipment. If you experience trouble, write for warranty and repair information.:

 For warranty and repair service outside the USA or Canada, please contact your distributor.
Canadian Notice 
The Industry Canada designation identifies certified equipment. This certification means that the equipment meets 

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal 

Equipment Technical Requirements document(s). Industry Canada does not guarantee the equipment will operate to 

the user's satisfaction.
Federal Communications Commission (FCC) Notice 
FCC registration number: This telephone equipment complies with Part 68, Rules and Regulations, of the FCC for 

connection to the Public Switched Telephone Network. 

Your connection to the Public Switched Telephone Network must comply with these FCC rules: 

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities 

of the local telecommunications company. The equipment must also be installed using an acceptable 

method of connection. The customer should be aware that compliance with the above conditions may not 

prevent degradation of service in some situations. See installation instructions for details. 

Use only an FCC Part 68-compliant Universal Service Order Code (USOC) network interface jack, as 

specified in the installation instructions, to connect to the Public Switched Telephone Network. 

If the equipment causes harm to the telephone network, the telephone company will notify you in advance 

that temporary discontinuance of the product may be required. But if advance notice isn’t practical, the 

telephone company will notify you as soon as possible. You will also be advised of your right to file a 

complaint with the FCC, if you believe it is necessary.

Ringer Equivalence Number (REN)
The REN provides an indication of the maximum number of terminals allowed to be connected to a telephone 

interface. The termination on an interface may consist of any combination of devices subject only to the requirement 

that the sum of the RENs of all the devices does not exceed 5.

The telephone company may make changes to its facilities, equipment, operations or procedures that 

could affect the operation of the equipment. If this happens, the telephone company will provide advance 

notice in order for you to make necessary modifications to maintain uninterrupted service.

Connection to party line services is subject to state tariffs. Do not connect this equipment to party lines.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation 

of this equipment does not disable your alarm equipment. If you have questions about what will disable 

alarm equipment, consult your telephone company or a qualified installer.

EMI/EMC (FCC Part 15)
NOTE:
 This equipment has been tested and found to comply with the limits for a Class A digital device, and as an 

intentional transmitter pursuant to Part 15 of the FCC Rules and Industry Canada RSS210 requirements. These limits 

are designed to provide reasonable protection against harmful interference. This equipment generates, uses and 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 

interference to communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures:

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

Consult the dealer. 

Save these instructions

North American Regulations - Please read Carefully

USA

Canada

Nortel Networks

640 Massman Drive

Nashville, TN, USA

37210

Nortel Repair Service Centre 30

30 Norelco Drive

Weston Ontario, Canada

M9L 2X6

Renseignements sur la réglementation et la sécurité 

 

Cet appareil de classe A est conforme aux sections 68 et 15 des règlements de la FCC et aux règlements adoptés par 

l’ACTA. Cet appareil est conforme aux spécifications ICES-0003 d’Industrie Canada concernant les interférences 

électromagnétiques. L’utilisation de cet appareil est soumise aux deux conditions suivantes : (1) Cet appareil ne doit 

pas provoquer d’interférences nuisibles et; (2) Cet appareil doit supporter les interférences, y compris celles 

susceptibles de nuire à son bon fonctionnement.

Le cas échéant, la réparation du matériel homologué doit être coordonnée par un représentant désigné par le 

fournisseur. En cas de réparations ou de modifications effectuées par l’utilisateur ou de mauvais fonctionnement du 

matériel, l’entreprise de télécommunications peut demander à l’utilisateur de débrancher l’appareil. Pour sa propre 

protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre du service public d’électricité, des lignes 

téléphoniques et des canalisations d’eau intérieures en métal, s’il y a lieu, sont raccordés ensemble. Cette mesure de 

sécurité est particulièrement importante dans les régions rurales. 

AVERTISSEMENT : L’utilisateur ne doit pas tenter d’établir lui-même le raccordement de mise à la terre. Il doit faire 

appel à un service d’inspection des installations électriques ou à un électricien, selon le cas. 
N’essayez pas de réparer cet appareil. Si vous avez des problèmes, communiquez par écrit pour obtenir de plus 

amples renseignements sur la garantie et la réparation de votre appareil :

 Pour toute question liée à la garantie et aux services de réparation hors des États-Unis et du Canada, communiquez avec 

votre distributeur.

Avis à l’intention des Canadiens 

La désignation Industrie Canada confirme que ce matériel est homologué. Elle atteste que le matériel est conforme 

aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications prescrites dans la 

documentation appropriée relative aux exigences techniques de l’équipement terminal. Industrie Canada ne garantit 

toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
Avis de la Federal Communications Commission (FCC) 

Numéro d’enregistrement de la FCC : Ce matériel téléphonique est conforme aux exigences de la section 68 des 

règlements de la FCC relatives au raccordement au réseau téléphonique public commuté. 

Le raccordement au réseau téléphonique public commuté doit être conforme aux règlements suivants de la FCC : 

Avant d’installer le matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de 

l’entreprise locale de télécommunications. Le matériel doit également être installé en suivant une méthode 

approuvée de raccordement. L’abonné doit savoir que la conformité aux normes énoncées ci-dessus ne 

constitue pas une garantie contre la possibilité d’une dégradation du service dans certaines conditions. 

Reportez-vous aux directives d’installation pour obtenir de plus amples renseignements. 

N’utilisez qu’une prise d’interface réseau du code de commande normalisée (USOC) conforme à la 

section 68 de la FCC, comme l’indiquent les directives d’installation, pour le raccordement au réseau 

téléphonique public commuté. 

Si l’équipement s’avère nuisible au réseau téléphonique, la compagnie de téléphone vous avisera à 

l’avance ou le plus tôt possible que vous devrez peut-être déconnecter temporairement le produit. Mais si 

elle ne peut vous informer à l’avance, elle vous informera le plus tôt possible. Vous serez également averti 

de votre droit de porter plainte auprès de la FCC.

Indice d’équivalence de sonnerie (IES)

Le IES fournit une indication du nombre maximal de terminaux qui peuvent être connectés à une interface 

téléphonique. La terminaison d’une interface peut être connectée à une combinaison de différents appareils tant que 

la somme des IES ne dépasse pas 5.

La compagnie de téléphone peut modifier ses installations, son équipement, son service ou ses 

méthodes, ce qui pourrait perturber le fonctionnement de l’appareil. Le cas échéant, la compagnie de 

téléphone vous avertira à l’avance pour que vous puissiez prendre les mesures nécessaires et éviter 

l’interruption de votre service téléphonique.

Une connexion au service de ligne partagée est soumise aux tarifs de l’État. Ne reliez pas ce matériel à 

des lignes partagées.

Si votre domicile est doté d’un système d’alarme relié à la ligne téléphonique, assurez-vous que 

l’installation de l’appareil n’empêchera pas le système d’alarme de fonctionner correctement. Pour des 

informations sur les installations de matériel pouvant perturber les systèmes d’alarme, consultez votre 

compagnie de téléphone ou un installateur.

EMI/EMC (section 15 de la FCC)

Remarque : Cet appareil a été testé et jugé conforme aux limites établies pour un émetteur numérique de classe A, 

conformément à la section 15 des règlements de la FCC et aux normes d’industrie Canada portant sur les interférence 

électromagnétiques. Ces limites visent à assurer une protection raisonnable contre les interférences pouvant nuire à 

l’appareil. Ce matériel génère des radiofréquences pouvant nuire aux communications s’il n’est pas installé et utilisé 

conformément aux instructions. L’exploitation de cet appareil dans un secteur particulier est toutefois susceptible de 

produire des interférences nuisibles. Si ce matériel cause des interférences nuisibles à la réception des émissions de 

radio ou de télévision, ce qui peut être vérifié en mettant l’éteignant et en le rallumant, l’utilisateur doit prendre l’une 

des mesures suivantes pour corriger la situation :

Réorienter ou relocaliser l’antenne de réception. 

Augmenter la distance entre l’appareil et le récepteur touché. 

Brancher l’appareil à une prise électrique d’un circuit différent de celui auquel le récepteur est branché. 

Consulter le détaillant. 

Conservez ces directives

Règlements pour l’Amérique du Nord – Veuillez lire attentivement ce qui suit

États-Unis

Canada

Nortel Networks

640 Massman Drive

Nashville, TN, USA

37210

Centre de service de réparations Nortel n°30

30, Norelco Drive

Weston Ontario, Canada

M9L 2X6

0.634637s