Ariston OK999 ELD PX AUSS Operating Instructions | Page 7

Ariston Ovens Operating Instructions - OK999 ELD PX AUSS.
Download
Page  of 20
4.1, 1845 votes
background image

AUS

7

Electrical Connection

The electrical connection to the mains must be made on 
the appliance. The power voltage and frequency are as 
indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

Fitting the power supply cable

1. Open the terminal board 
by inserting a screwdriver 
into the side tabs of the 
cover. Use the screwdriver 
as a lever by pushing it 
down to open the cover (see 
diagram)
.
2. Install the power supply 
cable by loosening the 
cable clamp screw and the 
three wire contact screws 
L-N-

.

Connect the wires to the 
corresponding terminals: 
the Blue wire to the terminal 
marked (N), the Brown wire 
to the terminal marked (L) 
and the Yellow/Green wire 
to the terminal marked 

 

(see diagram).

3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.

Connecting the power supply cable to the electricity 
mains

Install a standardised plug corresponding to the load 
indicated on the data plate (see opposite). 
The appliance must be directly connected to the mains using 
an omnipolar switch with a minimum contact opening of 3 
mm installed between the appliance and the mains.  The 
switch must be suitable for the charge indicated and must 
comply with current electrical regulations (the earthing wire 
must not be interrupted by the switch). The supply cable 
must be positioned so that it does not come into contact 
with temperatures higher than 50°C at any point (the back 
panel of the oven, for example).

! The installer must ensure that the correct electrical 
connection has been performed and that it is fully compliant 
with safety regulations.

Before connecting the appliance to the power supply, make 
sure that:
•  The appliance is earthed and the plug is compliant with 

the law;

•  The socket can withstand the maximum power of the 

appliance, which is indicated on the data plate (see 
below);

N

L

•  The voltage is in the range between the values indicated 

on the data plate (see below);

•  The socket is compatible with the plug of the appliance. 

If the socket is incompatible with the plug, ask an 
authorised technician to replace it. Do not use extension 
cords or multiple sockets.

!Once the appliance has been installed, the power supply 
cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by 
authorised technicians only (see Assistance).

! The manufacturer declines any liability should 
these safety measures not be observed.

APPLIANCE SPECIFICATIONS 

Dimensions* 

width 43.5 cm 
height 41 cm  
depth 41 cm  

Volume* 

74 l 

Dimensions**

 

width 45.6 cm 
height 41 cm  
depth 41 cm  

Volume**

 

77 l 

Electrical 
connections 

voltage: 220 - 240 V ~50 Hz 
maximum power absorbed 
3400 W (see data plate)  

ENERGY LABEL 

Directive 2002/40/EC on the 
label of electric ovens. 
Standard EN 50304 
 
Declared energy consumption 
for Forced convection 
Class – heating mode: 
ECO

 

 

This appliance conforms to the 
following European Economic 
Community directives: 
2006/95/EEC dated 12/12/06 
(Low Voltage) and subsequent 
amendments – 2004/108/EEC 
dated 15/12/04 
(Electromagnetic 
Compatibility) and subsequent 
amendments - 93/68/EEC 
dated 22/07/93 and 
subsequent amendments. 
2012/19/EEC and subsequent 
amendments. 
1275/2008 Stand-by/off mode

 

* Only for models with drawn rails.
** Only for models with wire rails.

0.601081s