Ariston LFF 8M 122 AUS Operating Instructions | Page 5

Ariston Dishwasher Operating Instructions - LFF 8M 122 AUS.
Download
Page  of 16
4.7, 1232 votes
background image

EN

5

Installation

* Only available in selected models.

If the appliance must be moved at any time, keep it in 

an upright position; if absolutely necessary, it may be tilted 
onto its back.

Connecting the water supply

Adaptation of the water supply for installation should only 

be performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards 
the right or the left in order to achieve the best possible 
installation. 
Make  sure  the  dishwasher  does  not  bend  or  squash  the 
hoses.

Connecting the water inlet hose
•  To a 3/4” gas cold or hot water connection point (max. 

60°C).

•  Run the water until it is perfectly clear. 
•  Screw the inlet hose tightly into position and turn off the 

tap.

If the inlet hose is not long enough, contact a specialist 

store or an authorised technician 

(see Assistance).

The water pressure must be within the values indicated 

in the Technical Data table - otherwise the dishwasher may 
be function properly.

Make sure the hose is not bent or compressed.

Connecting the water outlet hose
Connect the outlet hose to a drain duct with a minimum 
diameter of 2 cm. (A)
The outlet hose connection must be at a height ranging from 
40 to 80 cm from the floor or surface where the dishwasher 
rests.

Before connecting the water outlet hose to the sink drain, 
remove the plastic plug (B).

Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water 
supply in the event of anomalies or leaks from inside the 
appliance.
Some  models  are  also  equipped  with  the  supplementary 
safety device New Acqua Stop*, which guarantees anti-
flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut 
as it contains live electrical parts.

Electrical connection
Before inserting the plug into the electrical socket, make 
sure that:
•  The  socket  is  earthed  and complies with current 

regulations;

•  the  socket  can  withstand  the  maximum  load  of  the 

appliance as shown on the data plate located on the inside 
of the door 

 

(see chapter Description of the appliance);

•  The power supply voltage falls within the values indicated 

on the data plate on the inside of the door.

•  The socket is compatible with the plug of the appliance. 

If this is not the case, ask an authorised technician to 
replace the plug (

see Assistance). Do not use extension 

cables or multiple sockets.

Once the appliance has been instal ed, the power supply 

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced 

by the manufacturer or its authorised Technical Assistance 
Service in order to prevent all potential hazards. 

(See 

Assistance)

The Company shall not be held responsible for any 

incidents, if these regulations are not observed. 

Positioning and levelling
1. Position the dishwasher on a level sturdy floor. If the floor is 
uneven, the front feet of the appliance may be adjusted until 
it reaches a horizontal position. If the appliance is levelled 
correctly, it will be more stable and much less likely to move 
or cause vibrations and noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive 
transparent strip

* under the wooden shelf in order to protect 

it from any condensation which may form.

3. Place the dishwasher so that its sides or back panel are in 
contact with the adjacent cabinets or the wall. This appliance 
can also be recessed under a single worktop

* (see the 

Assembly instruction sheet).

4

*. To adjust the height of the rear foot, turn the red 

hexagonal bushing on the lower central part at the front of the 
dishwasher using a hexagonal spanner with an opening of 8 
mm. Turn the spanner in a clockwise direction to increase the 
height and in an anticlockwise direction to decrease it. 

(see 

Building-in instruction sheet attached to the documentation)

MIN 40 cm

MAX 80 cm

0.604208s