Ariston LBF 5BX Operating Instructions | Page 4
EN
4
Installation
* Only available in selected models.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
Positioning and levelling
1. Remove the appliance from all packaging and check that
it has not been damaged during transportation. If it has been
damaged, contact the retailer and do not proceed any further
with the installation process.
2.Arrangethedishwashersothatitssidesorbackpanelarein
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop
* (see the Assembly
Instruction sheet.)
3. Position the dishwasher on a level sturdy floor. If the floor
is uneven, the front feet of the appliance should be adjusted
untilitreachesahorizontalposition.Iftheapplianceislevelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
4
*. To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in an
anticlockwise direction to decrease it
(see Building-in Instruction
sheet attached to the documentation.)
Connecting the water and electricity supplies
Connection to the water and electricity supplies should only
beperformedbyaqualifiedtechnician.
The dishwasher should not stand on the water hoses or
electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Never use old or second hand hose sets. Do not reuse hose
sets from any previously installed dishwasher.
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
Connecting the water inlet hose
• Toasuitablecoldwaterconnectionpoint:beforeattaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
• Toasuitablehotwaterconnectionpoint:yourdishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
doesnotexceedatemperatureof60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician
(see Assistance.)
The water pressure must be within the values indicated in
the Technical Data table
(see adjacent information.)
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct with
a minimum diameter of 4 cm.
Theoutlethosemustbeataheightrangingfrom40to80cm
fromthefloor/surfacewherethedishwasherrests(A).
Before connecting the water outlet hose to the sink drain, remove
the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Somemodelsarealsoequippedwiththesupplementarysafety
device New Acqua Stop
*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstances should the water inlet hose be cut, as
it contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
• Thesocketisearthedandcomplieswithcurrentregulations.
• thesocketcanwithstandthemaximumloadoftheappliance,
which is indicated on the data plate located on the inside of
the door
(see Description of the appliance);
• Thepowersupplyvoltagefallswithinthevaluesindicatedon
the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.If
this is not the case, ask an authorised technician to replace
the plug (
see Assistance); do not use extension cables or
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
topreventallpotentialhazards
(see Assistance.)
Related Manuals for Ariston LBF 5BX
-
Baumatic Dishwasher BDW45.1 User's Manual
48 pages
-
Bosch Dishwasher SMV50C00GB Instruction Manual
28 pages
-
Diplomat Dishwasher ADP8352 User's Manual
10 pages
-
Electrolux Dishwasher ESF 63020 User's Manual
40 pages
-
Electrolux Dishwasher Diva Service Manual
32 pages
-
Fisher & Paykel Dishwasher DishDrawer DD603 I Service Manual
47 pages
-
Miele Dishwasher G 646 SC Operation Manual
68 pages
-
NEFF Dishwasher S5443X2GB Operation Manual
27 pages
-
Technika Dishwasher TBD4SS-2 User's Manual
6 pages
-
Whirlpool Dishwasher Whirlpool Dishwasher ADP6000IX User's Manual
13 pages
-
Hotpoint Dishwasher EXPERIENCE DISHWASHER FDFET 33121 User's Manual
20 pages
-
Westinghouse Dishwasher WSF6602 User's Manual
24 pages
-
DEFY Dishwasher DDW 157 User's Manual
18 pages
-
Fisher & Paykel Dishwasher 918TD User's Manual
21 pages
-
Maytag Dishwasher MDB4949SDM Installation Guide
76 pages
-
Maytag Dishwasher MDB4949SDM Use & Care Manual
42 pages
-
Maytag Dishwasher MDB5969SDM Use & Care Manual
42 pages
-
Maytag Dishwasher MDB8969SDM Use & Care Manual
42 pages
-
Miele Dishwasher G 6165 SCVi Futura Crystal Operating and Installation Instructions
80 pages
-
Miele Dishwasher G 6165 SCVi Futura Crystal Specification Sheet
5 pages
-
Miele Dishwasher G 6365 SCVi Specification Sheet
5 pages
-
Miele Dishwasher G 6560 SCVi Specification Sheet
5 pages
-
Frigidaire Dishwasher FFBD2406NS Installation Instructions
2 pages
-
Meiko Dishwasher K-200 Owner's Manual
32 pages