American Standard American Standard Multi-tool 2004 User's Manual

American Standard Multi-tool User's Manual - American Standard Multi-tool 2004.
Download
Page  of 4
4.5, 1783 votes
background image

S

A

VE FOR FUTURE USE

7 3 0 8 6 5 - 10 0   Rev.  M

P r o d u c t   n a m e s   l i s t e d   h e r e i n   a r e   t r a d e m a r k s   o f   A S   A m e r i c a ,   I n c .
©   A S   A m e r i c a ,   I n c .   2 0 11

CAUTION:  PRODUCT IS FRAGILE.  TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

 !

NOTE:  Pictures may not exactly define contour of china and components.

Thank you  for selecting American Standard - the benchmark of fine quality for over 100 years.  To ensure this product is installed properly, please read 
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONS  

Champion

®4

Model 2004 Normal Height Elongated One Piece Toilet
Model 2034 Right Height® Elongated One Piece Toilet

RECOMMENDED TOOLS AND  MATERIALS

Putty Knife
Closet Bolts

Regular Screwdriver
Wax Ring/Gasket

Adjustable Wrench
Flexible Supply Tube

Sealant
Hacksaw

Carpenters Level
Tape Measure

2

CLOSET
FLANGE

CLOSET

BOLTS

A

ROUGHING-IN DIMENSIONS:  
NOTE:  Distance from wall to closet flange centerline must be as listed below:

INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent 
damage), and install wax ring evenly 
around waste flange (horn), with tapered 
end of ring facing toilet.  Apply a thin
bead of sealant around toilet base.

POSITION TOILET ON FLANGE
a. 

Unplug floor waste opening and install toilet on closet 

        flange so bolts project through mounting holes.
b. 

Loosely install retainer washers and nuts. Side of 

 

washers marked "THIS SIDE UP" must face up!

4

5

3

WAX RING

SEALANT

Model 2004

29-3/4

(756mm)

8

(203mm)

1-3/4 (44mm)

 1-1/4
(32mm)

15

(381mm)

13-1/2

(343mm)

10-3/4

(273mm)

28-1/8

(714mm)

16-3/4

(425mm)

17-3/4

(451mm)

FINISHED WALL

18-1/2

(470mm)

C/L OF SEAT
POST HOLES
5-1/2 (140mm)
CENTERS

12

(305mm)

1/2 

(13mm)

10-3/4

(273mm)

4-1/2

(114mm)

SUPPLY 

AS 

REQ'D

*

FINISHED
FLOOR

7

(178mm)

4  

 (102mm)

CLOSET

BOLT

NUT

TAPERED
WASHER

 FLANGE

Recommended fitting type for back-to-back installations.

Depending upon your plumbing and venting conditions, the flow from 
the Champion in a back-to-back installation may create a vacuum on 
the system and draw water from the opposing bowl.  The National 
Standards Plumbing Code prohibits the use of a cross fitting for 
drainage as throw over is possible.  The code does approve a 
directional "Y" style fitting with proper venting to direct the water 
downward and away from the other toilet.

NOTE: BACK-TO-BACK INSTALLATION

REMOVE OLD TOILET

a.  Close toilet supply valve and flush tank completely.  Towel or sponge remaining water from tank and bowl.
b.  Disconnect and remove supply line.  NOTE:  If replacing valve, first shut off main water supply!
c.  Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.  Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
     NOTE:  Mounting surface must be clean and level

 before new toilet is installed!

1

Model 2034

29-3/4

(756mm)

8

(203mm)

1-3/4 (44mm)

 1-1/4
(32mm)

16-1/2

(419mm)

13-1/2

(343mm)

10-3/4

(273mm)

29-1/2

(749mm)

16-3/4

(425mm)

17-3/4

(451mm)

FINISHED WALL

 1 
(25mm)

 1 
(25mm)

18-1/2

(470mm)

C/L OF SEAT
POST HOLES
5-1/2 (140mm)
CENTERS

12

(305mm)

C/L OF OUTLET

C/L OF OUTLET

1/2 

(13mm)

10-3/4

(273mm)

4-1/2

(114mm)

SUPPLY 

AS 

REQ'D

*

FINISHED
FLOOR

7

(178mm)

3-3/4  

 (95mm)

INSTALL CLOSET BOLTS
Install closet bolts in flange 
channel, turn 90°, and slide into 
place 6" (152mm) apart and 
parallel to wall.

Related Manuals for American Standard American Standard Multi-tool 2004

0.615653s