Actron Battery/Alternator Tester CP7611 User's Manual

Actron Automobile Battery Charger User's Manual - Battery/Alternator Tester CP7611.
Download
Page  of 2
4.9, 1022 votes
background image

CP7611 Battery/Alternator Tester
USER MANUAL
1. SAFTY RULES
This tester is designed for “TOUCH” testing only. Do not keep con-

tinuous contact with the circuit under test for over 10 seconds.

Do not use the tester if the tester or test leads look damaged, or if

you suspect that the tester is not operating properly. When using

the tester, keep your fingers behind the finger guards on the tester

and black test lead. Always ensure that the probes are dry and do

not use the tester when your hands are wet.
Warning:  Never attempt to test any circuits were 120vac might be

present, such as 120vac outlets, electrical tools, and appliances.

Doing so can cause a serious personal injury and will damage the

tester!

2. ELECTRICAL SPECIFICATIONS
The LEDs (Light Emitting Diodes) located on the front panel of the

tester indicate the presence of the following dc voltages in the cir-

cuit under test: 5V, 12V, 12.5V, 13.5V, 14.0V, and 15.0V
3. OPERATION
TEST PREPARATIONS:
1.  Before testing, make sure the battery and terminals are clean, all

electrical connections are good and alternator belts are tight.

2.  Use the same test points to check the battery and alternator.

Touch the negative probe to the negative [-] battery terminal, and

touch the positive probe to the positive [+] battery terminal.
BATTERY TEST:

1. Turn the engine OFF.

2. Touch the negative probe to the negative [-] battery terminal and

the positive probe to the positive [+] battery terminal.

3.  Observe the 3 LEDs located in the Battery area of the tester front

panel to find the battery condition.

4.  If the reading is low, the battery might be discharged.  Recharge

the battery and repeat the test.

ALTERNATOR TEST:
1.  Start the engine and operate it at 2000 RPM (or other setting

recommended by the vehicle manufacturer).

2. Touch the negative probe to the negative [-] battery terminal and

the positive probe to the positive [+] battery terminal.

3.  Observe the 3 LEDs located in the Alternator area of the tester

front panel to find the condition of the alternator and other compo-

nents of the charging system.

4. MAINTENANCE:
This tester has no serviceable parts.
Periodically wipe the tester with a soft damp cloth and mild house-

hold detergent. Do not use abrasives and solvents.  Ensure that no

water gets inside the tester to prevent possible damage.

Probador de Batería y Alternador

CP7611

MANUAL DEL USUARIO

1. REGLAS DE SEGURIDAD
Este probador está diseñado para pruebas BREVES o DE TOQUE

(‘TOUCH’). No mantenga contacto continuado con el circuito bajo

prueba durante más de 10 segundos. No use el probador si el mismo

o sus terminales de prueba se ven dañados, o si usted sospecha

que el probador no está operando correctamente. Al usar el probador,

mantenga  sus  dedos  detrás  de  las  protecciones  para  dedos  del

probador y el terminal de prueba negro. Asegúrese siempre de que

las sondas estén secas; si sus manos están húmedas, no use el

probador.
Advertencia:  No intente nunca probar circuitos en los que pudiera

haber presencia de 120 V CA, tales como tomacorrientes de tensión

de línea de 120 V CA, herramientas eléctricas y electrodomésticos. ¡El

hacerlo puede causar serias lesiones personales, y dañará al probador!

2. ESPECIFICACIONES ELECTRICAS
Los LEDs (Diodos Emisores de Luz) ubicados en el panel frontal del

probador indican la presencia de las siguientes tensiones de CC en

el circuito bajo prueba: 5 V, 12 V, 12,5 V, 13,5 V, 14,0 V y 15,0 V.
3. OPERACION

PREPARACION DE LAS PRUEBAS:

1.  Antes de comenzar las pruebas, asegúrese de que la batería y

sus terminales  estén limpios, todas las conexiones eléctricas estén

bien, y las correas del alternador tengan la tensión correcta.

2.  Use los mismos p untos de prueba para verificar la batería y el

alternador. Toque con la sonda negativa el terminal negativo (-) de

la batería, y toque con la sonda positiva el terminal positivo (+) de la

batería.
PRUEBA DE LA BATERIA:
1.  Lleve el motor al estado APAGADO (OFF).

2.  Toque con la sonda negativa el terminal negativo (-) de la batería,

y toque con la sonda positiva el terminal positivo (+) de la batería.

3.    Para  conocer  la  condición  de  la  batería,  observe  los  3  LEDs

ubicados en el área de Batería del panel frontal del probador.

4.  Si la lectura es baja, la batería podría estar descargada. Recargue

la batería y repita la prueba.

Related Manuals for Actron Battery/Alternator Tester CP7611

0.516857s