A.O. Smith GPS-75 Owner's Manual | Page 9
9
3. Make sure that plastic tubing is still attached to the pressure
switch and fan housing. Also make sure that wiring connector
from motor to control box is securely attached.
4. Do not plug in power cord until vent system is completely
installed. The Power Vent operates on 120 Vac, therefore a
grounded outlet must be within reach of the 6 foot flexible
power cord supplied with the vent (see fig.1). The power cord
supplied may be used on unit only where local codes permit.
If local codes do not permit use of flexible power supply cord:
A. Remove screws that hold cover plate on control box and
remove plate.
B. Cut flexible power cord on inside of control box, as close
to inside wall as possible.
C. If flexible cord and strain relief are removed, then opening
in box must be covered by a plastic cap on the front side
of the control box.
D. Remove plastic cap on the right side of control box and
install suitable conduit fitting in enclosure.
E. Splice field wiring into existing wiring using code
authorized method (wire nuts, etc).
F.
Be certain that neutral and line connections are not
reversed when making these connections.
G. Ground heater properly. This water heater must be
grounded in accordance with the National Electric Code
ANSI/NFPA70 and/or local codes. These must be followed
in all cases.
The water heater must be connected to a grounded metal,
permanent wiring system; or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment grounding terminal or lead
on the water heater, see Figure 7.
H. Replace cover plate and secure with two screws.
5. The blower discharge boot is made to accept only straight
sections of 3" pipe. To start off with an elbow, a short section
of the furnished pipe, a minimum of 2 inches, must be cut
and glued into the end of the elbow that will mount on the
discharge boot (see fig. 6).
POWER VENT WIRING SCHEMATIC - FIGURE 7
CAUTION
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN
CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
Related Manuals for A.O. Smith GPS-75
-
A.O. Smith Water Heater BTX-100 Specification Sheet
2 pages
-
A.O. Smith Water Heater Cyclone BFC - 60 Installation Manual
98 pages
-
A.O. Smith Water Heater EES - 52 Specification Sheet
4 pages
-
A.O. Smith Water Heater ProMax Power-Vent GPVH-50 Instruction Manual
32 pages
-
A.O. Smith Water Heater Promax Short ECS-40 Instruction Manual
28 pages
-
A.O. Smith Water Heater Promax Tall ECT-52 Instruction Manual
28 pages
-
A.O. Smith Water Heater Promax Tall ECT-55 Instruction Manual
28 pages
-
A.O. Smith Water Heater Promax Tall ECT-80 Instruction Manual
28 pages
-
Electrolux Water Heater EWH-SL/SLN User's Manual
4 pages
-
Whirlpool Water Heater E1F50RD045V User's Manual
16 pages
-
Whirlpool Water Heater Energy Smart EE2H40RD045V User's Manual
15 pages
-
Rheem Water Heater Ruud G100-200(A) User's Manual
2 pages
-
Redring Water Heater 1070810E User's Manual
8 pages
-
GSW Water Heater SUPERFLUE POWER VENTED GAS FIRED WATER HEATER User's Manual
18 pages
-
Rheem Water Heater Professional Prestige Series: Hybrid Heat Pump Use & Care Manual
24 pages
-
Rheem Water Heater Tankless Electric RTE 13 Use & Care Manual
16 pages
-
A.O. Smith Water Heater GCVL-40 Technical Documents
32 pages
-
A.O. Smith Water Heater ATI-540H-N Technical Documents
64 pages
-
Rinnai Water Heater RUR98i (REU-KBP3237FFUD-US) Specification Sheet
2 pages
-
Rinnai Water Heater RUR98i (REU-KBP3237FFUD-US) Operation and Installation Manual
61 pages
-
Rinnai Water Heater RUC80i (REU-KBD2530FFUD) Operation and Installation Manual
140 pages
-
Rinnai Water Heater RUC98i (REU-KBD3237FFUD) Operation and Installation Manual
140 pages
-
Rinnai Water Heater RUC98i (REU-KBD3237FFUD) Specification Sheet
2 pages
-
Rinnai Water Heater RL94i (REU-VC2837FFUD-US) Specification Sheet
2 pages