A.O. Smith ATO-340H-P Technical Documents | Page 6

A.O. Smith Water Heater Technical Documents - ATO-340H-P.
Download
Page  of 6
4.1, 1518 votes
background image

PRESSURE LOSS

Residential/Commercial Gas
Tankless Water Heaters

Page 6 of 6

www.hotwater.com

AOSRG46835

For Technical Information call 1-877-737-2840. A. O. Smith Corporation reserves the right to make product changes or improvements without prior notice.

Ϭ

ϮϬ

ϰϬ

ϲϬ

ϴϬ

ϭϬϬ

ϭϮϬ

Ϭ

ϱ

ϭϬ

ϭϱ

ϮϬ

Ϯϱ

ϯϬ

ϯϱ

ϰϬ

ϰϱ

ϱϬ

ĞƐƐƵƌ

Ğ

>ŽƐƐ

;ƉƐŝͿ

,ĞĂĚ

;&

ĞĞƚͿ

Ϭ

ϮϬ

ϰϬ

ϲϬ

ϴϬ

ϭϬϬ

ϭϮϬ

Ϭ

ϱ

ϭϬ

ϭϱ

ϮϬ

Ϯϱ

ϯϬ

ϯϱ

ϰϬ

ϰϱ

ϱϬ

ĂĚ

;&

Ğ

Ğƚ

Ϳ

ĞƐƐƵƌ

Ğ

>ŽƐƐ

;Ɖ

ƐŝͿ

+

+

  

,ĞĂĚ

;&

ĞĞƚͿ

ĞƐƐƵ

ƌĞ

>ŽƐƐ

;ƉƐŝͿ

&ůŽǁƌĂƚĞ ;'WDͿ

6HWWHPSHUDWXUHÛ)Û&RU ORZHU
6HWWHPSHUDWXUHÛ)Û&RUKLJKHU

+

3UHVVXUH /RVV

)ORZ 5DWH *30

3UHVVXUH /RVV

)ORZ 5DWH *30

3UHVVXUH /RVV

)ORZ 5DWH *30

Specification

Water heater(s) shall be Model_________________ as manufactured by A. O. Smith Water Heaters, shall be a copper coil integral fin and tube construction with quick release brass or bronze waterways. Heater(s)
will be factory assembled and tested.

The heater shall be vented with 3” or 4” Schedule 40 PVC, CPVC, or ABS vent pipe, or stainless steel Category III vent pipe at a distance not to exceed 70’ (equivalent) for 3” vent or 100’ (equivalent) for 4” vent,
terminating vertically or horizontally as prescribed. Intake air pipe may be of such material as ABS, PVC, galvanized B-Vent, corrugated aluminum or stainless steel, or Category IV stainless steel not to exceed
70’ (equivalent) for 3” vent or 100’ (equivalent) for 4” vent.

The heater(s) shall be controlled by an onboard solid-state printed circuit board monitoring incoming and outgoing temperatures with factory installed thermistors, sensing and controlling flow rate to set point
temperature, controlling both air and gas mixture inputs to maintain thermal combustion efficiency. The heater(s) shall also consist of inline fusing, a spark ignition and sensor system, aluminized stainless steel
burners, an air-fuel ratio sensor, a hi-limit temperature switch, modulating and proportional gas valves, a freeze protection sensor with ceramic heating blocks, and an overheat cutoff fuse.

The water heater(s) shall be CSA listed, exceed the energy efficiency requirements of ASHRAE 90.1b-1992, and shall comply with SCAQMD Rule 1146.2 Ultra-Low NOx Standards.

Related Manuals for A.O. Smith ATO-340H-P

0.664191s