Troy-Bilt CS 4325 Chipper Shredder Owner's Manual | Page 13
Service
7
13
7.
Install a replacement blade (Part No. 742-0544) with the
hardware removed earlier or sharpen.
IMPORTANT: When sharpening the blade, protect hands by
using gloves. Follow the original angle of grind and make
sure to remove an equal amount from each blade.
8.
To replace the other blade, rotate the impeller to expose
the second blade and repeat the steps above.
NOTE: Make certain blades are reassembled with the sharp
edge outward (toward the chipper chute). Torque hardware
to between 20 ft.-lbs and 25 ft.-lbs.
Shredder Blade
WARNING: The shredder blade is sharp. Wear
leather work gloves to protect your hands.
1.
Stop engine, disconnect spark plug, and make certain that
all moving parts have come to a complete stop.
2.
Remove the two flange nuts (and hex bolts) which secure
the hopper support bracket to the impeller housing. Retain
the hardware. See Figure 7-2.
Figure 7-2
3.
Pivot the shredder screen upward as instructed under the
heading Cleaning the Reduction Chamber.
Blade Care
Chipper Blades
WARNING: The impeller’s chipper blades are
sharp. Wear leather work gloves to protect your
hands.
1.
Stop engine, disconnect spark plug, and make certain the
chipper shredder has come to a complete stop.
2.
Pivot the shredder screen upward as instructed under the
heading Cleaning the Reduction Chamber.
3.
Remove the chipper chute support brace from the frame
by removing the two hex bolts and saddle washers which
secure it. See Figure 7-1A.
A
C
B
Model Series CS 4325 Shown
Figure 7-1
4.
Remove the chipper chute by removing three hex nuts and
washers which secure it to the impeller housing. See Figure
7-1B.
5.
Rotate the impeller by hand until one of the two chipper
blades is visible through the impel er housing opening.
6.
Remove the blade by removing the internal hex screws,
lock washers and hex nuts which secure it to the impeller.
See Figure 7-1C. Retain the hardware.
NOTE: Use a 3/16” hex key (Allen) wrench on the outside of
the blade and a 1/2” box (or socket) wrench on the inside of
the impeller. Hold the Allen wrench stationary and rotate
the box (or socket) wrench to loosen the nut.
Related Manuals for Troy-Bilt CS 4325 Chipper Shredder
-
Logitech Misc Electronics O-R0004 Quick Start Manual
2 pages
-
Brother Misc Electronics DB2-B755 MKIII Owner's Manual
4 pages
-
Panasonic Misc Electronics KX-TG6572R Owner's Manual
64 pages
-
Technics Misc Electronics SA-AX720 Owner's Manual
36 pages
-
RCA Misc Electronics RCR504BR Owner's Manual
2 pages
-
RCA Misc Electronics RCRN04GR Owner's Manual
2 pages
-
RCA Misc Electronics RCRBB04GR Owner's Manual
6 pages
-
Intermatic Misc Electronics GM40AVE Owner's Manual
12 pages
-
Intermatic Misc Electronics ET70115 and ET70215 Owner's Manual
20 pages
-
Intermatic Misc Electronics ET1705C Owner's Manual
4 pages
-
Kidde Misc Electronics Firex 2650-560,2650-561 English MA2650 Owner's Manual
6 pages
-
Trane Misc Electronics XL800 Owner's Manual
8 pages
-
Trane Misc Electronics XL803 Owner's Manual
8 pages
-
Trane Misc Electronics XL624 Owner's Manual
8 pages
-
Trane Misc Electronics XL600 Owner's Manual
8 pages
-
Trane Misc Electronics XL80 Owner's Manual
12 pages
-
Trane Misc Electronics XR80 Owner's Manual
12 pages
-
Trane Misc Electronics XB80 Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics TB146 EC 4-Cycle Garden Cultivator Owner's Manual
16 pages
-
Troy-Bilt Misc Electronics TB516 EC Lawn Edger Owner's Manual
12 pages
-
Troy-Bilt Misc Electronics Colt FT Garden Tiller Owner's Manual
36 pages
-
Linear Misc Electronics AP-4 Owner's Manual
2 pages
-
Brother Misc Electronics KE-430F Parts Manual
68 pages
-
Hunter Misc Electronics XC Programming Instructions Manual
18 pages